anyone know what is "cell with Zero maximum clock transition time"  ?

not zero transition, not maximum transtion, it is zero maximum clock transition time.

it means X0 cell? (drive-strength)

can you explain? 

thanks :-)

Hi,

Is there any way to instruct the tool to reduce the low metals effort and route more on top layers? 

Hi there, 

we've encountered some strange behavior when trying to run the "check_litho" command from within INNOVUS 22.14. We set the required files and configuration files according to our PDK documentation. The command, without the absolute file paths, is:

check_litho -sign_off -cpu 96 -run_mode fg -create_guides -map_file <map file path> -config <config file path> -techfile <tech file path> -dir <output dir path> -write_stream_options "-mode ALL -merge <list of gds files>" -apply squishHints

We are currently using PEGASUSDFM 23.20 for this command but tested previous PEGASUSDFM and MVS versions as-well. After we issued the previous command, we see INNOVUS launching the PEGASUSDFM/MVS and trying to run the command. After some time, the command crashes with the error "mdb_load_with_extra: failed to pre-open extra input file './preproc/INTERMEDIATE.oas' for read". We have tested a similar setup with INNOVUS 19.10 where we did not have this issues. Did something change with the new INNOVUS version? Does anyone have an idea what we are missing? 

Thanks in advance.

Best regards,

PS

Hi everyone,

I'm designing a digital chip that will be fabricated. I have a HDL top module that includes several submodules inside it. I want to define the position of some of the submodules during the PnR so that later I can specify there positions in the Micrograph photo after the IC fabrication. When I perform the PnR using Innovus, I always got a layout shape where the submodules seems to be flatted. I wonder if there is a way to specify the placement of each submodule in my top module  (maybe in the tcl file) during the PnR so later I can define there positions in the micrograph photo. 

Thanks in Advance!

Hi everyone,

I'm new to using Innovus and I'm encountering an issue while trying to perform the "init_design" command. My goal is to perform the place and route. Here are the commands I'm using:

``
set init_verilog ./test.v
set init_top_cell TEST
set init_pwr_net {VDD VDD_2 VDD_3}
set init_gnd_net {VSS VSSA}
set init_lef_file { /home/laumecha/uw_openroad_free45/pdk/Drexel-ECEC575/Encounter/NangateOpenCellLibrary/Back_End/lef/NangateOpenCellLibrary.lef}
set init_mmmc_file {./viewDefinition.tcl}
init_design
```

However, I receive the following error:

```
#% Begin Load netlist data ... (date=06/04 12:07:50, mem=1478.7M)
*** Begin netlist parsing (mem=1439.0M) ***
Created 0 new cells from 0 timing libraries.
Reading netlist ...
Backslashed names will retain backslash and a trailing blank character.
**ERROR: (IMPVL-209):   In Verilog file './test.v', check line 16 near the text # for the issue: 'syntax error'.  Update the text accordingly.
Type 'man IMPVL-209' for more detail.
Verilog file './test.v' has errors!  See above.

*** Memory Usage v#1 (Current mem = 1439.027M, initial mem = 634.098M) ***
#% End Load netlist data ... (date=06/04 12:07:50, total cpu=0:00:00.0, real=0:00:00.0, peak res=1478.7M, current mem=1478.7M)
**ERROR: (IMPVL-902):   Failed to read netlist ./test.v. See previous error messages for details.  Resolve the issues and reload the design.
```

However, the file works perfectly in Genus.

It seems there is a syntax error in my Verilog file at line 16, but I'm not sure how to resolve it. Any guidance or suggestions would be greatly appreciated.

Thanks in advance!

I am trying to remove the cdn_loop_breaker cells from the netlist. 
When I tried the below 2 things, genus synthesis tool removing the cdn_loop_breaker cells but while connecting the cdn_loop_breaker cell input to its proper connection, its somehow misleading the connections

Things i tried:
1.  remove_cdn_loop_breaker -instances *cdn_loop_breaker*
then i just ran remove_cdn_loop_breaker  comand without the -instances switch
2. remove_cdn_loop_breaker  
     
both of the above things are not providing the proper connections after removing the loop_breaker_cells

can anyone suggest the best possible workaround for this please?

Hi all,

I have been following the tutorial "Innovus Block Implementation with Stylus Common UI", version 23.1.

While I was doing the clock tree synthesis, the tutorial calls for a command

clock_opt_design

But my tool tells me this is a beta feature which needs to be enabled.

Warning: clock_opt_design requires beta feature innovusClockOptFlow enabled.

Can I ask how do I enable this beta feature?

My version of Innovus is v21.35-s114_1, is it because of the version incompatibility?

Many thanks

We are currently setting up the Tempus flow and have ran into some mismatched data regarding ECO and timing reports. I generated a timing report before running ECO and saw six total setup violations. When running opt_signoff -setup, the initial setup summary that was printed in the shell only showed one violation. I can see that violation from the initial setup summary in my pre-ECO timing report and it is not the worst path. Upon further investigation, I forced the tool to try to fix setup on one of the other five violations from the timing report using the opt_signoff_select_setup_endpoints attribute and the tool said that the endpoint had positive slack and would be ignored.

Has anyone experienced something like this before?

Hi, I'm using genus (Version 21.14-s082_1) to synthesis a VHDL-design with multiple power-domains. After reading the power intent file and calling 'apply_power_intent',  I get the following warning:

Warning : Potential problem while applying power intent of 1801 file. [1801-99]
: Cannot find any instance for scope '/:CHIP_TOP'. Rest of commands in this scope will be skipped (set_scope:../../upf/CHIP_TOP.upf:2).
: Check the power intent. If the scenario is expected, this message can be ignored.

The fist two lines of CHIP_TOP.upf:

upf_version 3.1
set_scope :CHIP_TOP

I simulated the same  UPF and VHDL files with Xeclium and was able to verify all the IEEE1801/UPF aspects I need without any problems. I don't know, why genus is having a problem with the 'scope'.
In genus, after getting the warning, running 'set_db power_domain:CHIP_TOP/BLOCK_A/PD_CORE_D .library_domain PD0V5' returns the following error:

Error : <Start> word is not recognized. [TUI-182] [set_db]
: 'power_domain:CHIP_TOP/BLOCK/PD_CORE_D' is not a recognized object/attribute. Type 'help root:' to get a list of all supported objects and attributes.
: Check if the given <Start> word is a valid object_type, object or attribute.

Running 'commit_power_intent' gives me:

Started inserting low power cells...
====================================
Info : Command 'commit_power_intent' cannot proceed as there are no power domains present. [CPI-507]
: Design with no power domains is 'design:CHIP_TOP'.
Completed inserting low power cells (runtime 0.00).
====================================================

I'm suspecting that the problem lies in 'set_scope' and VHDL. I never had such problems with Verilog. I tried every way to reference the hierarchy in the code and now I'm at my wit's end and I need your help o/
How to set the scope with 'set_scope' in UPD 3.1 to the toplevel in VHDL, so that genus accepts it? Or is the problem caused by something else?

Best,

Iqbal

Hi all,

I have off grid violations on M2 layer. I have tried ecoRoute -fix_drc and deleting violations and rerouting. But the tool is still placing these routes off grid. The on grid option in nanoroute is turned on. Since there is a fat metal closer to these routes, the tool is honouring the drc and not placing the metals on track. How do I ignore drc while routing? Also if there is any other way I can fix it, please let me know 

Hi all, while saving design, there is an error saying a net has tid problem. However the design is saved. Does anybody know how to resolve the Tid problem?

I am getting the cut_spacing violation in the power plan, my design has two power rails, and the via is not formed for two rails, only one rail getting via, I used edit power via and modified the cut_space violation.

how to solve this problem.

Hi all,

I'm trying to model the clock of a clock doubler. The doubler consists of a delay cell and an XOR gate, which generates a pulse on both the rising and falling edge of the input clock. I've created a simple module to evaluate this. In this case, DEL1 and XOR2 are standard library cells. There is a don_touch constraint on both library cells as well as on clk_d.

module top (
input wire clk,
output reg Q);

//Doubler
wire clk_d;
wire clk_2x;
DEL1 u_delay (.I(clk),.Z(clk_d));
XOR2 u_xor (.A1(clk),.A2(clk_d),.Z(clk_2x));

//FF for connecting the clock to some leaf:
always @(posedge clk_2x) Q<=~Q;

endmodule

My SDC looks like this:

create_clock [get_ports {clk}] -name clk_i -period 100
set_clock_latency -rise 0.1 [get_pins u_xor/Z]
set_clock_latency -fall 0.4 [get_pins u_xor/Z]
create_generated_clock -name clk_2x -edges {1 1 2 2 3} -source clk [get_pins u_xor/Z]

The generated clock is correctly generated but the pulse width is zero. I would be expecting that the pulse width is the difference between fall and rise latency but is not applied:

report_clocks:

report_clocks -generated:

clk_2x is disconnected from the FF after syn_generic. What can I do to model some minimum pulse width? Will innovus later on model this correctly with the delay of DEL1?

With digital implementation rapidly advancing, how do you think iOS and Android platforms will continue to evolve in industries like healthcare or education? The integration of mobile technology is already revolutionizing these fields, and it would be interesting to discuss where this could lead and what new opportunities might emerge.

for debug I use suspend in my tcl script to debug，here is the code

after that the innovus command screen become 

how to quit the SUSPEND status？ thanks

Hi all, 

I have made a custom cell in Innovus that I will be instantiating into a bigger block, which I will also be using Innovus to do the Place & Route. 

I understand that I can generate a *.lef file and a *.lib file using Innovus. However, I need to also create a *.db file (these format of files are often used in DC Compiler synthesis tool). 

Is there a way to create the *.db file from Innovus? Or, is there a tool that I can use to create this *.db file? 

Thank you for your time. 

I'm trying to write a generic piece of code that will return the layermap file location, with file name, for a variety of projects (which could potential have different layermap file naming conventions. The below code is what I've used to date, but this assumes the file name is xxxx.layermap. I can obviously do some string matching to find it, assuming the various files all contain some common characters. I thought I'd ask if there is a simpler way to find it, I know that this information is automatically loaded into the Xstream out gui, so maybe I can use the same approach to find it.

techLibName=techGetTechFile(cv)~>libName

techLibLayerMap=strcat(ddGetObj(techLibName)~>readPath "/" techLibName ".layermap")

Hi everyone. 

I'm very a new cadence user. I'm not good at using it and quite lost in finding a way to get the results. With the topic, I would like to ask you for some suggestions to improve my cadence skills.

I have some digital decision logic. Some are combinational logic, some are sequential logic that I would like to import or generate random input combination to the inputs of my decision logic to get the maximum, minimum, and average delay power dissipation and area when feeding the different input combination.

My logic has 8-bit, 16-bit, and 32-bit input. The imported data tends to be decimal numbers.

I would like to ask you:

- which tool(s) are the most appropriate to import and feed the different combination to my decision logic?

- which tool is the most appropriate to synthesis with different number of input? - I have used Genus Synthesis Solution so far. However with my skill right now I can only let Genus synthesize my Verilog code one setup at a time. I'm not sure if I there is anyway I can feed a lot of input at a time and get those results (min, max, average of delay, power dissipation and area)

- which language or scripts I should pick up to use and achieve these results?

-where can I find information to solve my problem? which information shall I look for?

Thank you so much for your time!!

Best Regards

IR criteria:

Static IR (STD) ~2%

Static IR (MEM) ~1%

Dynamic IR (STD) ~10%

Dynamic IR (MEM) ~5%

Anyone knows the reason behind this criteria? >.<

I have a 2-dimensional input in my design - input [2:0] data_in [15:0]. After synthesis with genus, I got a netlist where the inputs are like data[15], data[14],...,data[0]. And furthermore it has definitions like input [2:0] data[15], .... So how can I define the pin locations of each of the bits for this input? Can I define data[15]'s inner bits like data[15][0]? Is it possible to define this with def files?

Hello All,

How do we control the Always on buffering for a power domain called B in Power domain A.

here B-power domain nets going through A , hence tool is inserting Always on buffers.

How do we avoid this specific power domain ?

Thanks,
Bshaik

Hi! I've made some 1-point waveform "markers" that I want to overlay in my plots to aid visualization (with the added advantage, w.r.t. normal Viva markers, that they update location automatically upon refreshing simulation data).

For example, the plot below shows an spectrum along with two of these markers, which I create with the function "singlePointWave", and the Assembler output definitions also as shown below.

The problem is: as currently created and defined, Assembler is unable to plot these elements. I can send their expressions to the calculator and plotting works from there, BUT ONLY after first enabling the "Allow Any Units" in the target Viva subwindow.

Thus, I suspect Assembler is failing to plot my markers because they "lack" other information like axes units and so on. How could I add whatever is missing, so that these markers can plot automatically from Assembler?

Thanks in advance for any help!

Jorge.

P.S. I also don't know why, but nothing works without those "ymax()" in the output definitions--I suspect they are somehow converting the arguments to the right data type expected by singlePointWave(). Ideas how to fix that are also welcome! ^^

procedure( singlePointWave(xVal yVal)
    let( (xVect yVect wave)
        xVect = drCreateVec('double list(xVal));
        yVect = drCreateVec('double list(yVal));
        wave = drCreateWaveform(xVect yVect);
    );
);

I am trying to install IC231 on RHEL 8 using installscape, however configuring keeps failing.

I tried to run the configuration file manually as suggested in one of the previous posts and it gives me following errors:

sh batch_configure.sh
/home/rs/cadence/installs/IC231/install/tmp/slconfig.sh: line 165: xterm: command not found
cat: ncvhdl23.03-d103lnx86_101124125631.stat: No such file or directory
rm: cannot remove 'ncvhdl23.03-d103lnx86_101124125631.stat': No such file or directory
/home/rs/cadence/installs/IC231/install/tmp/slconfig.sh: line 165: xterm: command not found
cat: ncvhdl64b23.03-d103lnx86_101124125631.stat: No such file or directory
rm: cannot remove 'ncvhdl64b23.03-d103lnx86_101124125631.stat': No such file or directory
/home/rs/cadence/installs/IC231/install/tmp/slconfig.sh: line 165: xterm: command not found
cat: oaRedist22.61-p003lnx86_101124125631.stat: No such file or directory
rm: cannot remove 'oaRedist22.61-p003lnx86_101124125631.stat': No such file or directory
/home/rs/cadence/installs/IC231/install/tmp/slconfig.sh: line 165: xterm: command not found
cat: amsEnv64b23.10-p043lnx86_101124125631.stat: No such file or directory
rm: cannot remove 'amsEnv64b23.10-p043lnx86_101124125631.stat': No such file or directory
/home/rs/cadence/installs/IC231/install/tmp/slconfig.sh: line 165: xterm: command not found
cat: ihdl64b23.10-p043lnx86_101124125631.stat: No such file or directory
rm: cannot remove 'ihdl64b23.10-p043lnx86_101124125631.stat': No such file or directory

I am not very well versed with Linux at the moment but trying. Could any one suggest something or point to what is missing?

Hi! 

I am attempting to create a very simple test pcell that contains a single Nmos 4 terminal device (Gate, Source, Drain, Backgate). However, unlike other devices I have used in the past, the backgate terminal of the device I wish to include within the pcell is an inherited connection, and the other 3 are physical terminals. Note that for the pcell master, I do not want any inherited connections, just physical pins. Hence I need to drive this inherited connection with a pin within my pcell. I started implementing the symbol and schematic first, ensuring I could obtain the correct connectivity, extract netlist, etc. I thought I had it hooked up correctly, but alas I am failing to export the CDL. Let me explain my current approach.

Schematic:

Create the 4 physical pins using a combination of dbCreateInst (for the pin isnt), dbMakeNet, dbCreateTerm and dbCreatePin.

Create the device instance using dbCreateInstByMasterName and setting the desired cdf parameters + callbacks.

For the physical terminals of the device, I'm using dbCreateConnByName to make the connection to the appropriate net that was created above.

For the inherited connection, I am creating a netSet property like so: dbCreateProp(newinst deviceTermName "netSet" netName)

Symbol:

Create the 4 physical pins using a combination of dbCreateRect, dbMakeNet, dbCreateTerm, dbCreatePin.

And then create whatever symbol design I wish using the likes of dbCreateRect, dbCreateLine, etc. 

Everything works fine when using a device without an inherited connection, so I'm guessing I'm missing something along this line... Also, if I copy the contents of the pcell schematic to a regular schematic view, do a check and save, the view extracts just fine. So I wonder if the check and save it fixing the connectivity that I may not have. 

Thanks for any possibly engagement or suggestions 🙂

Keelan

Hi,

I am looking to perform a net trace in a CDL file.

There is a net at a lower level and would like to know the net it is connected to at the top level.

Please let me know if there is a way to analyze the CDL file to perform this net trace.

Thanks,

Mallikarjun.

I want to create sub tree of sub trees how can i do that?

I want to create another tree for the Sub parameter also.

Is there a skill command for "Assign Layout Instance terminals", this form appears when i click on define device correspondence and Bind the devices.

Also,

Problem Statement : i have a schematic with a couple of transistor symbols and and i alos have a corresponding layout view with respective layout transistors but they all are inside a pCell(created by me) i.e layout transistor called inside a custom Pcell. Now i have multiple symbols in schematic view and a single instance(pCell) in layout view. 
Is there a way how i can bind these schematic symbols with layout symbols inside the pCell(custom)? Even if i have to use cph commands i'm fine with it. need help here.

The idea here is to establish XL connectivity between the schematic symbols and corresponding layout transistors(inside the pCell).

Thanks,

Shankar

Hello Community,

Is there any simple way how i can get the coordinates of all the shapes in a layout view?

Currently i'm flattening the layout, getting all the lpps from CV and using setof to get all the shapes of a layer and looping through them to get the coordinates.

Is there a way to do it without having to flatten the layout view and shapes merged or any other elegant way to do it if we flatten it?

Also, dbWriteSkill doesn't give output how i desired

Thanks,

Shankar

Hi,

I hope you are doing well.

I have designed and simulated a PA system in Cadence using high-level blocks, which include both ideal components and some defined with Verilog-A. My goal is to calculate the Bit Error Rate (BER) and Error Vector Magnitude (EVM) in the system. I am using an LTE source from RFLib, and everything functions correctly in the transient simulation.

To calculate these parameters, I intended to use envelope simulation. However, when I attempt to run the envelope simulation, I encounter convergence errors, which prevent it from working as expected.

Given this issue, I believe I need to work with transient data instead. Could you please advise on how to approach this in Cadence without exporting the data to MATLAB?

Thank you for your assistance.

What is the variable to define via selection/type for vias

I want to be able to load via cut type in the via option when I use the leHiCreateVia() function

I want to select/load to the Via Option menu on which via I want to use

Cadence version IC23.1.64b.ISR7.27

Paul

I am attempting to use dbGetNeighbor() function inside the dynamic display HUD so that the distance to the next metal on that layer could be viewed. Think of another line in this dynamic table here... 

My SKILL code is essentially the following:

procedure(getNearestNeighborOnMetal(cv)
let((direction tmpBoundingBox)
direction = internal_function()
tmpBoundingBox = dbCreateRect(geGetEditCellView() "tmp" list(hiGetCommandPoint() hiGetCommandPoint()))
car(dbGetNeighbor(geGetEditCellView() tmpBoundingBox direction))
)
)

this returns the distance to the closest metal based on some tests.

Next, I try to register this function to work in the Dynamic Display / Info Balloon world by executing odcRegisterCustomFunc() for each and every object type (I know, absurd, but trying to debug)

In the dynamic display menu, I toggle the "Custom SKILL Function" check in layoutXL, then hit apply, then OK.

After this I find I am unable to view the changes reflected in any info balloons or in the drawing HUD (above) for this wire. I have tried replacing my function with the sample "customFunc" from the odcRegisterCustomFunc() documentation and was still unable to produce any new output.

Any help diagnosing the use of this feature would be very much appreciated

Hello,

When I draw a Fluid Guard Ring in Virtuoso, the layout is not visible, and instead, "do_something=nil" appears.

When I check the details with Q, it shows the same information as a regular NFGR guard ring, and Ctrl+F also displays the instance name, just like with a regular NFGR. 

Additionally, the Pcells of Fluid Guard Rings from previous projects appear broken. 

The version I’m currently using is not different from the one used in the past. Even when I access the same version as the one used during the project, the Pcells still appear broken.

These two issues are occurring, and I’m not sure what to check. I would greatly appreciate it if you could assist me in resolving this issue.

//

Hi,all

  I want to remove some Tests form adexl automatically,there have any function to achieve that?

Hi,

My query is regarding importing of layout.

After importing, we see that the imported transistor instances and vias are all referring to the library in which they are imported, instead of referring to the technology library.

Please let me know how we can refer them to the technology library.

Will surely provide more details if my query is unclear.

Thanks,

Mallikarjun.

Hello,

I would like to create a button for my form that prompts the user to click on a cellview and draw a rectangle bounding box, exactly like the one used in the Area and Density Calculator. Can someone please help me with this?

Thanks!

Beto

Hello Community,

I have encountered an issue that is a mystery to me and hope somebody could give me a clue about what is happening in Cadence and maybe even a solution?

I am running a test scripted in a SKILL file that sequentially opens two different projects with MC analyses and in between I get an error message box and also multiple logs in CIW with exactly the same text.

Both projects run a simulation with a call like this:

historyName = maeRunSimulation(?session sessionName ?waitUntilDone t)

After this the script closes the current project, opens the next project and executes the same line with maeRunSimulation() for the second project. Then immediately this error message happens, and also is logged repeatedly in the CIW window

The message box looks like this:

The logs I get in CIW:

nil
hiCancelProgressBox(_axlNetlistCreateProgressBar)
nil
hiCancelProgressBox(_axlUILoadForm)
nil
when(dwindow('axlDataViewessWindow1) hiMapWindow(dwindow('axlDataViewessWindow1)))
t
when(dwindow('axlRunSummaryessWindow1) hiMapWindow(dwindow('axlRunSummaryessWindow1)))
t
ERROR (ASSEMBLER-1600): Cannot find an active session named fnxSession0.
You can only modify an ADE Assembler session that is active.
Perhaps the session name was misspelled or has not yet been created.
Verify the session name matches an existing ADE Assembler session.

1>
ERROR (ASSEMBLER-1600): Cannot find an active session named fnxSession0.
You can only modify an ADE Assembler session that is active.
Perhaps the session name was misspelled or has not yet been created.
Verify the session name matches an existing ADE Assembler session.

*WARNING* hiDisplayAppDBox: modal dbox 'adexlMessageDialog' is already displayed!
ERROR (ASSEMBLER-1600): Cannot find an active session named fnxSession0.
You can only modify an ADE Assembler session that is active.
Perhaps the session name was misspelled or has not yet been created.
Verify the session name matches an existing ADE Assembler session.

*WARNING* hiDisplayAppDBox: modal dbox 'adexlMessageDialog' is already displayed!
ERROR (ASSEMBLER-1600): Cannot find an active session named fnxSession0.
You can only modify an ADE Assembler session that is active.
Perhaps the session name was misspelled or has not yet been created.
Verify the session name matches an existing ADE Assembler session.

Hi guys,

I see that inside VNC I can’t resize window boxes by mouse. While pressing the arrow at the box edge and dragging it nothing happens:

is it a bug, or setup change require?

Noted, it only happens when trying to resize window box from left and right side..

Thx

Hi All,

I'm using a code (abConvertPolygonToPath.ils) that I found in other posts to convert a rect object to a path object inside a pcell code, but when I try to run a DRC, the layout export fails due to a warning message, here is the log message

*WARNING* (DB-270001): Pcell evaluation for 18A_asaavedr/lay_mesh_BM0_BM4_3p6_3p6/layout has the following error(s):

*WARNING* (DB-270002): ("eval" 0 t nil ("*Error* eval: undefined function" abConvertPolygonToPath))

ERROR (XOASIS-231): Pcell evaluation failed for '18A_asaavedr/lay_mesh_BM0_BM4_3p6_3p6/layout' because the Pcell SKILL code contains either a syntax error or an unsupported XOasis function. Check the standard output or the Virtuoso log file for more information. Cadence recommends correcting the Pcell SKILL code to resolve the issue. However, to ignore these errors and continue the translation, you may use the 'ignorePcellEvalFail' option.

INFO (XOASIS-282): Translation Failed. '1' error(s) and '3' warning(s) found.

And when compile the code I get the following message:

*WARNING* defgeneric function already defined - abConvertPolygonToPath

I will aprreciate any help in how to waive this error, or fix it.

Thank you

Disappearing toolbar or docked menu

Is there a way for the toolbar or floating menu from disappearing when a cells tab is added to a window?

I have created a skill toolbar and it disappeared when I add another cell or tab to a window.

The only toolbars that stay are the ones I have defined in the Layout.toolbar file.

Do I have to add a trigger to keep the toolbars visible or not disappearing from the window?

Cadence version IC23.1-64b.ISR7.27

Paul

Hi,

I want to define a procedure that with @key, and I also want to restrict the variable's datatype, I tried with folloing but I received error in CIW

procedure(tt(handler @key str1 str2 "ssS")
  printf("handler: %L " handler)
)

tt('test)

The error is like: *Error* tt: argument for keyword ?str1 should be a symbol (type template = "ssS") at line 11 of file

Thanks,

James

Hello,

I was looking to destructively and efficiently modify a list that was passed in as an argument to a procedure, by prepending an item to the list.

I noticed that cons lets you do this efficiently, but the operation is non-destructive. Hence this wouldn't work if you are trying to modify a function's list parameter in place.

Here is an example of trying to add "0" to the front of a list:

Hi there

I am trying to make cross-probe btw layout and schematic view.

so when I execute the code in schematic using bindkey, the code will raise the layout view (hiRaiseWindow)

and then I want to descend to the same hierarchy as schematic. (geSelectFig, leHiEditInPlace)

But looks like current cellview still stays at schematic view.

I got this error msg, and when I print current cell view name at where I got this msg, it replys schematic.

*Error* geSelectFig: argument #1 should be a database object (type template = "d") - nil

is there any way to change the current cellview to layout view?

I also added this code, but didn't work.

geGetEditCellView(geGetCellViewWindow(cvId)) ;cvId is layout view

I don't want to close the schematic view, just want to move the focus or make geSelectFig works.

Thanks in advance.

A new Python library has been written to facilitate an interface between Python and AWR software using a command structure that adheres more closely to Python coding conventions. This library is labeled "pyawr-utils" and it is installed using the standard Python pip command. Comprehensive documentation for installing and using pyawr-utils is available.(read more)

When starting a new design, it's important to take the time to consider design recommendations that prevent problems that can arise later in the design cycle. This two-part compilation of guidelines for starting a new design is the result of years of Cadence AWR Design Environment platform Support experience with designs. Pre-design decisions for user interface, simulation, layout, and library configuration lay the groundwork for a successful and efficient AWR design. This blog covers the user interface (UI) and simulation considerations designers should note prior to starting a design.(read more)

by Sherry Hess In this new blog series, Max Maxfield gets to know Zeke, an amazing 11-year-old with a dream to speak with the astronauts on the International Space Station (ISS). His first step on this journey however began with becoming a HAM r...(read more)

Thermal analysis with the Cadence Celsius Thermal Solver integrated within the AWR Microwave Office circuit simulator gives designers an understanding of device operating temperatures related to power dissipation. That temperature information can be introduced into an electrothermal model to predict the impact on RF performance.(read more)

Cadence AWR Design Environment Software Featured in Multiple Training Course Options: Live and Virtual Starting in October(read more)

The Cadence AWR Design Environment V22.1 production release is now available for download at Cadence Downloads with design environment, AWR Microwave Office, AWR VSS, AWR Analyst, and other enhancements.(read more)

AWR V22.1 software introduces the Pointer-Hybrid optimization method which uses a combination of optimization methods, switching back and forth between methods to efficiently find the lowest optimization error function cost. The optimization algorithm automatically determines when to switch to a different optimization method, making this a superior method over manual selection of algorithms. This method is particularly robust in regards to finding the global minima without getting stuck in a local minima well.(read more)