RF Design Solutions for Next-Generation Products The International Microwave Symposium (IMS2022), otherwise known as Microwave Week, was recently held (June 19-24) at the Denver Convention center, returning to its long-standing g...(read more)

With the latest release (Sigrity and Systems Analysis 2022.1 HF2) of Clarity  3D Solver, support for encrypted component models is now available. With this functionality, vendors that supply 3D components, such as connectors, can now merge their...(read more)

The silkscreen layer plays a crucial role in the assembly, repair, and testing of a PCB. You can add a variety of information to this layer, such as the location of the components, polarity, component orientation, on-off switches, LEDs, and testpoint...(read more)

Microwaves & RF's David Maliniak interviews Sherry Hess of Cadence about recently announced products of Optimality and OnCloud.(read more)

The Allegro PCB Editor Basic Techniques course provides all the essential training required to start working with Allegro® PCB Editor. The course covers all the design tasks, including padstack and symbol creation, logic import, constraints setup...(read more)

Dear All,

To design an outphasing combiner, I need to extract the input impedances when the circuit is driven by two sources concurrently with a varying phase-shift and plot them on a Smith Chart. However, I can't find a way to display the simulated S-parameters on a Smith Chart.

The testbench, shown below, consists of two sources set to 50 Ohm with variable phase (PORT0: theta, PORT1: -theta) swept from -90° to 90°. The NPORTs are couplers used to isolate the forward and reflected power at each source, i.e. the S-parameters are:

• S13 = S31 = 1; through path
• S21 = S41 = 1; forward and reflected power
• All other are zero

The testbench is simulated with an "hb" analysis instead of "sp", as the two sources have to be excited simultaneously with varying phase-shift to see their load-modulation effect. The sweep is setup in the "Choosing Analysis" window. The powers of the forward (pXa) and reflected (pXb) waves are found through the "Direct Plot" window, e.g. pvr('hb "/p1a" 0 50.0 '(1)) as the power for p1a, and named P1A_Watt. The S-parameters are then calculated as the reflected power w.r.t. the forward power P1B_Watt/P1A_Watt. This approach is based on a Hot S-parameter testbench from ADS.

At this point I would like to display these S-parameters on a Smith Chart. However, this seemed more challenging than expected. One straightforward method would seem to create an empty Smith Chart window in the Display Window and dragging the S-parameters from the rectangular plot on it, but this just deletes them from the Display Window. Hence my question:

How can I display these S-parameters on a Smith Chart?

Dear all,

Hi!

I'm trying to do a Harmonic Balance (HB) Large-Signal S-Parameter (LSSP) simulation to figure out the input impedance of a nonlinear circuit.

Through this simulation, what I want to know is the large-signal S11 only (not S12, S21 and S22).

So, I have simulated with only single port (PORT0) at input, but LSSP simulation is terminated and output log shows following text.

" Analysis `hb' was terminated prematurely due to an error "

The LSSP simulation does not proceed without second port.

Should I use floating second port (which is not necessary for my circuit) to succeed the LSSP simulation?

Does the LSSP simulation really need two ports?

Below figure is my HB LSSP simulation setup.

Additionally, Periodic S-Parameter (PSP) simulation using HB is succeeded with only single port.

What is the difference between PSP and LSSP simulations?

Hi, newbie here.

We are using AWR Design Enviroment in our university and so I have to install it (OS: Arch Linux)
I installed it in a Windows 10 VM without problems.

When I try to start it prompts "Failed to connect to license server", I guess thats the first problem.

After that when trying to generate my SUL License it will prompt Internal Error -8 (see Image)

I can't find something on Error -8 :/ and overall the available data to the license topic is quit low :/

If someone has a solution for that I would gladly hear about it :)

Hello, Currently i am designing a 96MHZ crystal oscillator using pierce topology and also I use for amplitude gain control circuit for regulation. The problem is when i run a PSS + Pnoise i get these warnings :

WARNING (CMI-2375): M2: Vgs has exceeded the oxide breakdown voltage of `vbox' = 6 V.
WARNING (CMI-2375): M4: Vgs has exceeded the oxide breakdown voltage of `vbox' = 6 V.
WARNING (CMI-2377): M4: Vgd has exceeded the oxide breakdown voltage of `vbox' = 6 V.
WARNING (CMI-2377): M3: Vgd has exceeded the oxide breakdown voltage of `vbox' = 6.6 V.

and also WARNING (CMI-2682): M5: The bulk-drain junction forward bias voltage (1.38154 V) exceeds VjdmFwd'=851.514mV ,The results are now incorrect because the junction current model has been linearized

Note : i am using Supply 1.2 V hence it is not possible to exceed the oxide breakdown. 

So i am asking why i am getting these warnings , it could be a convergence problem and the Results computed are not corrected.

Also when running DC and transient , i don't get these warnings.

Hi,
My Virtuoso and Spectre Version: ICADVM20.1-64b.NYISR30.2
I plot an eye diagram using a built in function. I want to see the data-dependent jitter. I want to measure the eye diagram edges at zero crossing (width of that diamond part) shown in the pic by vertical and horizontal markers. I can put a marker and read the numbers there and get what I want. But now I want to run Monte Carlo and I can't do this for all samples. I wish I could write an expression for this. Unfortunately, I see that the function "cross" is not working on the eye diagram. Basically, when I send the eye diagram data to a table, I see that it actually is just the prbs data and not the eye diagram data. Is there a hack that can help me achieve my goal which is: having an expression to measure the edges of the eye diagram at zero crossing?
There is a script that Andrew wrote (https://support.cadence.com/wps/mypoc/cos?uri=deeplinkmin%3AViewSolution%3BsolutionNumber%3D11395772). This is a good script but it puts all edges on top of each other. I want to distinguish the two edges. In the attached pic (two-period eye diagram) you can see what I mean by the two edges (diamond shapes). I want to measure each of the two and take the maximum. Having all the edges on top of each other won't give me what I want. All edges together will lso include DCD. I purely want to measure DDJ. DCD is measured separately. I have very little experience with writing scripts and could not modify Andrew's script.
Your help is much appreciated. Thank you.

Hello,

I am trying to design an RF mixer for a TX.
Assume my input IF signal is at 1 GHz, my LO at 2 GHz and I want my RF at 3 GHz, and assume that the mixer fully works after testing it with HB.
How to simply set the envelope analysis to check the EVM ?
I read through the documentation but I couldn't get it (I couldn't fully understand the settings of the source, probe, analysis.)
Which source and probe to use? I want custom modulation with custom bandwidth and center frequency.
Is there some examples for the ENVLP analysis ?

I am using IC23.1 and spectre 20.1.354.

Hi,

In our design team, we're looking for a strategy to make all cell views self-contained. We are struggling to do so when nport devices are involved.

The nport file requires a full path, whereas what we need is a relative path to the current path of the cell in which we're using the nport.

I have browsed through the forums & cadence support pages, but could not find a solution.

1) There is a proposal from Andrew to add the file directory in ADE option "Simulation Files." :https://community.cadence.com/cadence_technology_forums/f/rf-design/27167/s-parameter-datafile-path-in-nport . This, however, is not suitable, because the cell is not self contained.

2) The new cadence version off DataSource "cellView" in nport options:

This however is not suitable for us due to two reasons:

i- Somehow we don't get this option in the nport cell (perhaps some custom modification from our PDK team)

ii- Even if we had this option, it requires to select the library, which again makes it unsuitable: We often copy design libraries for derivative products using "Hierarchical Copy" feature. And when the library is copied, the nport will still be pointing to the old library. Thus, it is still not self-contained.

In principle, it should not be difficult (technically) to point to a text file relative to the cell directory (f.ex we can make a folder under the same cell with name "sparFiles" & place all spar files under this folder), however it does not seem to be possible.

Could you perhaps recommend us a work-around to achieve our goal: making the cells which contain nport devices self-contained so that when we copy a cell, we do not have to update all the nport file destinations ?

Thanks in advance.

My Cadence Version: IC23.1-64b.ISR4.51

My Spectre version: 23.1.0.362.isr5

Hi *,

I am simulating a 32kHz high Q crystal oscillator with a pulse shaping circuit. I set up a PSS analysis using the Shooting Newton engine. I set a beat frequency of 32k and used the crystal output and ground as reference nodes. After the initial transient the amplitude growth was already pretty much settled such that the shooting iterations could continue the job.

My problem is: In 5...10% of my PVT runs the simulator detects a frequency divider in the initial transient simulation. The output log says:

Frequency divided by 3 at node <xxx>

The Estimated oscillating frequency from Tstab Tran is = 11.0193 kHz .

However, the mentioned node is only part of the control logic and is always constant (but it has some ripples and glitches which are all less than 30uV). These glitches spoil my fundamental frequency (11kHz instead of 32kHz). Sometimes the simulator detects a frequency division by 2 or 3 and the mentioned node <xxx> is different depending on PVT - but the node is always a genuine high or low signal inside my control logic.

How can I tell the simulator that there is no frequency divider and it should only observe the given node pair in the PSS analysis setup to estimate the fundamental frequency? I have tried the following workarounds but none of them worked reliably:

- extended/reduced the initial transient simulation time

- decreased accuracy

- preset override with Euler integration method for the initial transient to damp glitches

- tried different initial conditions

- specified various oscillator nodes in the analysis setup form

By the way, I am using Spectre X (version 21.1.0.389.ISR8) with CX accuracy.

Thanks for your support and best regards

Stephan

I get multiple results at the same frequency in a 3-tone simulation.

I try to determine the IP3 of a mixer. I have 3 large signal tones: 0.75 GHz, 1.25 GHz and 1.26 GHz.

At the IM3 frequency of 490 MHz I observe 4 results, see also the screenshot of the table output. The frequencies are exactly the same (even when I subtract 490 MHz by using xval() ).

Which of the values do I have to use to determine the correct IP3?

Is there an option to merge these results?

Hello everybody,

As you can find in the attached image, I am trying to simulate a Colpitts oscillator. However, using pss analysis it shows a high output power. 

My question is where is the problem of my structure or simulation setup?

Best,

Hello everyone,

I am trying to perform a load pull simulation of a transistor to verify some gain calculations I made using its S-parameters. Specifically, I have calculated the optimal conjugate impedances for the input and output to later calculate the power dissipated and transmitted in each stage of the transistor. Then, I only varied the output impedance and recalculated these powers, noticing that the power delivered to the load is lower.

Now, what I want to do is simulate this behavior using the Load Pull simulation. I have taken the model shown in the image, but I believe it is a linear model. My question is: if the chosen model is linear, is the load pull simulation accurate? In the calculations I made, nonlinearities are not considered. I don’t want to take nonlinearities into account.

In short, do you have any ideas on how to verify the calculations made with the transistor’s S-parameters through a load pull simulation?

Can you recommend any transistor model that is nonlinear and also has an S-parameter file?

Thank you very much in advance.

Hello everyone,

For my cross-coupled oscillator design, I have a problem with stability analysis. Based on my achieved results which are attached, where is my design problem?

Best,

https://ibb.co/bgKFP4N

https://ibb.co/3FGRLmV

https://ibb.co/pwSZDSF

Hi everyone,

I'm currently working on my thesis, which involves a beamformer system using CMOS 65nm technology. I'm trying to use the EMX tool for EM simulation but have encountered a few problems. Before diving into my questions about EMX, let me briefly explain how I conduct EM simulations with other software (ADS).

In ADS, I use the EM simulator with the Momentum microwave engine. However, my EM layout is quite large, and the mesh generated is extremely detailed, making it difficult to simulate the entire system. As a workaround, I divide the system into smaller parts and simulate each one individually. I've attached a snapshot of my setup, which includes an amplifier and a 1-to-2 Wilkinson power divider. I've separated these circuits and placed pins to facilitate EM simulations for each. I also placed ground pins at the boundaries of each circuit to connect them to the ground plane.

Here’s the link to the image (I'm unable to upload it due to an error): https://drive.google.com/file/d/13Qn4-DvMBj_K1JQLXrTWaWZ8uaLJr15u/view?usp=sharing

Now, moving on to EMX (version 6.3). For a maximum frequency of 31 GHz, I set the edge mesh = thickness = 0.4 µm (approximately the skin depth). However, when I simulate the circuit (amplifier + divider), the mesh on the ground plane becomes very dense, which makes running the simulation impossible due to excessive memory requirements. I reverted to my ADS approach and divided the circuit into two parts, placing ports to connect them. Unfortunately, EMX doesn't allow me to place multiple edge ports on the same edge for the ground plane, which has left me confused. Here are a couple of questions I have:

1. Is breaking the circuit into smaller parts a valid approach? Given the large ground plane, the mesh size for the ground is significant, making simulations challenging. Are there any methods to manage this issue?

2. Regarding the ground pins, why can't I place multiple edge ports to connect the ground planes of both circuits as I did in ADS? If this approach is incorrect, could you suggest alternative methods for simulating individual circuits and connecting them to estimate system performance?

Any insights would be greatly appreciated. Thank you in advance for your help!

Hello Everybody

Recently, I want to design a high output Power Amplifier at 2.4GHz using TSMC 1P6M CMOS Bulk Process. I use its nmos_rf_25_6t transistor model to determine the approximate mosfet size

I use the most common Common-Source Differential Amplifier topology with neutralizing capacitor to improve its stability and power gain performance

Because I want to output large power, the size of mosfet is very large, the gate width is about 2mm, when I perform harmonic balance analysis, everything is alright, the OP1dB is about 28dBm (0.63Watt)

But When I perform Transient simulation, the magnitude of voltage and current waveform at the saturation point is too small, for voltgae, Vpeaking is about 50mV, for current, Ipeaking is about 5mA

I assume some reasons: the bsim4 model is not complete/ the virtuoso version is wrong (My virtuoso version is IC6.1.7-64b.500.21)/the spectre version is wrong (spectre version is 15.1.0 32bit)/the MMSIM version is wrong/Transient Simulation setting is wrong (the algorithm is select gear2only, but when I select other, like: trap, the results have no difference), the maxstep I set 5ps, minstep I set 2ps to improve simulation speed, I think this step is much smaller than the fundamental period (1/2.4e9≈416ps)

I have no idea how to solve this problem, please help me! Thank you very very much!

An AMS Designer Flex simulation gives you the most immediate access to the latest simulation technology on either side, gets out of the way of the core engines and allows the engine performance to shine while providing access to new features. Check out this blog to know more.

Che(read more)

This blog introduces you to an efficient way to debug interface elements or connect modules in a mixed-signal simulation.(read more)

Read this blog for an overview to the Circuit physical verification and parasitic extraction design stage in the Custom IC Design methodology and the key design steps which can help you achieve this.(read more)

This blog describes how to efficiently use Virtuoso Visualization and Analysis XL.(read more)

I am trying to figure out the most efficient workflow for adding test points. My use case involves adding ~100 or so SMT pads at the bottom for bed-of-nails ICT test that are required to be on a test point grid. A lot of the nets are on the top or from inner layers and so have to be brought to the bottom using stubs. I'm used to Xpediiton workflow of being able to set a test point padstack, set a test point grid, and then select a net, add the test point to the bottom layer on the grid with that net attached and then route the stub with gridless routing.

In Orcad, it seems I need to route the stub, switch layer pairs to be both bottom once I bring the stub to the bottom and then change the grid to be the test point grid and then add the test point on the grid. It requires a lot of clicks, very mistake prone requiring lots of oops and very slow for 100+ test points to be brought out at the bottom. 

I'm sure there is a better way that is used by folks with a lot of Orcad experience. Any suggestions?

hello

is there a way to update one dynamic shape instead of updating all dynamic shapes?

i have over 6000 dynamic shapes on my design and it takes over 10 mins to update them all.

i just would like to update only one dynamic shape sometimes to find out if placing vias and lines in a shape has enough space or not.

regards

masa

The default behaviour of Place replicate update is to select every new net item connected to the replicate module. This leads to an abundant number of clines, vias and shapes being selected, most of which I don't want to add to the replicate group. It is very tedious to unselect all these items and more often than not, I miss one or two items and then end up with a via or cline in a completely different place on the board or outside of the board.

Is there a way to change this rather annoying behaviour? I haven't found any way to disable it or to batch deselect everything the tool has decided to add to the replicate group.

The question has been asked before, but it didn't get any answers and the thread is now locked.

/F

I am using OrCAD PCB Designer Standard version 17.4-2019. I want to force update the Package_Height_Max property on the place bound top shape. The footprint library that we've created has that property set in the dra file, but I'd like to override that from capture so I can be certain that the height is correct.

This is coming from a place where we have created a very large footprint library over that past ++ years. Everyone who creates a new footprint is supposed to make sure that we add Package_Height_Max to the footprint, but of course footprints get reused for various parts, not all of which will have the same package height. What I want to do is export a list of package heights from our part database and then import the package heights into Capture and override the package height in the footprint.

I have found a post here  Using Height Property from Orcad Capture which says its not possible, but it also says its from 15 years ago, so maybe things have changed?

Any tips or SKIL files to help create a thermal shaped openings for paste masks for a donut shaped pin for mics or stand-offs like below?

Hai Community,

What are the differences between the Cadence OrCAD / Allegro 24.1 with the Altium Designer 24.

Can I get the grid matrix difference between these two tools?

Regards,

Rohit Rohan

Socionext, a leader in SoC design, recently made significant strides in enhancing its design efficiency for a complex billion-gate project. Faced with the initial challenges of lengthy eight-day iterations and a protracted two-month timing signoff process, the objective was to reduce the iteration cycle to just three days. By integrating Cadence's cutting-edge solutions—Certus Closure Solution, Tempus Timing Solution, and Quantus Extraction Solution—Socionext achieved remarkable improvements.

Notably, the Tempus DSTA tool dramatically cut timing closure time by 73%, outperforming conventional single-machine STA methods. This achievement, combined with the synergistic use of Cadence's Certus Closure and Tempus Timing solutions, allowed Socionext to meet their ambitious three-day iteration target and double productivity. Additionally, integrating these solutions significantly decreased both human and machine resource needs, slashing memory and disk costs by up to 90% and halving engineering resources during the optimization and signoff phases.

For more on this collaboration, check out the "Designed with Cadence" success story video on Cadence's website and YouTube channel.

Also, don't miss the on-demand webinar "Fast, Accurate STA for Large-Scale Design Challenges," which provides a deeper dive into Socionext's breakthroughs and the innovative solutions that powered their success.

The blog discusses Voltus InsightAI RAK that is designed to give you an accelerated start on the execution of Voltus InsightAI flow.(read more)

The world of electronics design thrives on efficient tools that bridge the gap between concept and silicon. Virtuoso Digital Implementation is a powerful ally for mixed-signal designs, which integrate both analog and digital components. This blog post will examine Virtuoso Digital Implementation's capabilities and explore how it can streamline your mixed-signal design workflow.

Virtuoso Digital Implementation in a Nutshell

Virtuoso Digital Implementation is a license package within the Cadence Virtuoso Design Platform. It offers a streamlined RTL-to-GDSII flow to implement smaller digital blocks within a mixed-signal design environment. Here's what makes Virtuoso Digital Implementation stand out:

• Focus on Small Digital Blocks: Optimized for digital blocks with an instance count of up to 50,000 (expandable to 150,000 with specific configurations), Virtuoso Digital Implementation is ideal for integrating digital logic into your analog-centric design.
• Leveraging Industry Leaders: Virtuoso Digital Implementation utilizes cut-down versions of the renowned Cadence Genus Synthesis Solution and Innovus Implementation System under the hood. This ensures you get access to proven technologies for logic optimization and place-and-route.
• Seamless Integration with the Virtuoso Environment: Virtuoso Digital Implementation's key advantage is its tight integration with the Virtuoso Layout Suite. You can launch the synthesis and place-and-route tools directly from the Virtuoso environment, eliminating the need to switch between platforms.

Benefits of Using Virtuoso Digital Implementation

 By incorporating Virtuoso Digital Implementation into your mixed-signal design flow, you can get several benefits:

• Simplified Workflow: Virtuoso Digital Implementation offers a centralized environment for both digital block implementation and layout editing within the Virtuoso environment. This reduces context switching and streamlines the design process.
• Faster Time-to-Market: Virtuoso Digital Implementation's streamlined workflow can significantly reduce design turnaround times, allowing you to get your product to market quicker.
• Improved Design Quality: Leveraging industry-leading synthesis and place-and-route engines from Cadence ensures high-quality digital block implementation within your mixed-signal design.

Who Should Consider Virtuoso Digital Implementation?

 Virtuoso Digital Implementation is a valuable tool for anyone working on mixed-signal designs with smaller digital blocks. It's particularly well-suited for:

• Analog IC designers who need to integrate digital logic into their designs.
• Circuit design teams working on mixed-signal applications like data converters, power management ICs, and RF transceivers.

Virtuoso Digital Implementation provides a compelling solution for designers working on mixed-signal projects. Its streamlined workflow, tight integration with the Virtuoso design platform, and access to proven digital design tools can significantly improve design efficiency and time-to-market. Virtuoso Digital Implementation is worth considering if you're looking to optimize your mixed-signal design flow.

I am here to help and guide you on how to learn more about Virtuoso Digital Implementation flow.

Welcome to Virtuoso Digital Implementation, an online course recently released. This course teaches implementing digital blocks using Cadence tools based on the Virtuoso Digital Implementation flow. Also, you can download a lab database after the lecture and get hands-on experience in each stage.

Want to Enroll in this Course?

We organize this Virtuoso Digital Implementation training for you as a "Blended" or "Live" training. Please reach out to Cadence Training for further information.

Register for the Online Training with the following steps:

• Log on to cadence.com with your registered Cadence ID and password.
• Select Learning from the menu > Online Courses.
• Search for Virtuoso Digital Implementation using the search bar.
• Select the course and click Enroll.

And don't forget to obtain your Digital Badge after completing the training!

Related Resources

Online Courses

• Cadence RTL-to-GDSII Flow v6.0
• Virtuoso Digital Implementation Training

Training Byte Videos

• How Do You Run Placement Optimization in the Innovus Implementation System?
• How to Run the Synthesis Without DFT?
• How to Run the Synthesis Flow with DFT?
• Creating Power Rings, Power Stripes, and Power Rails in the Innovus Implementation System
• How to Run Power Analysis and Analyze the Results in Innovus?

Happy Learning!

A more appropriate title for this blog could be “All Vehicles with ADAS Need the Midas Functional Safety Platform”.

EVs tend to have advanced driving assistance systems (ADAS) because they’re newer, but not all vehicles with ADAS are EVs!

Certifying Advanced Driver Assistance Systems (ADAS) is a multifaceted process involving rigorous testing, validation, and regulatory compliance to ensure safety and reliability.
As ADAS technologies become increasingly sophisticated, the certification process is evolving to meet these challenges.

The ISO26262 standard provides the requirements to be met to attain safety certification for digital designs.

One of the key aspects of ADAS certification is functional safety. This includes:

• Ensuring the system operates as intended under all conditions, including failures.
• Adherence to standards like ISO26262.
• Rigorous testing to identify potential hazards and mitigate risks.

The Midas Safety Platform provides early-phase exploration of functional safety architectures and leverages native chip design data to perform accurate safety analysis efficiently.

The platform is a unified solution available across Cadence products, and with its modular architecture, it supports both embedded and standalone usage with the Cadence flow.

After extracting the design information, an output Midas database file contains the isolated DUT and provides the design components and their fault tolerances to various tools in the flow.

Conformal can easily verify design transformations that include necessary components like TMR for safety.

In these videos, we explore how to create reports for both Transient and Permanent faults.

Creating Detailed FMEDA in Midas (Video)

Creating Architectural FMEDA in Midas (Video) 

Also, read this blog post for additional motivation: What Is Zonal Architecture? And Why Is it Upending the Automotive Supply Chain?

What Next?

Join the Midas Safety Platform Introduction and the Functional Safety Implementation and Verification with Midas trainings and learn more about:

• Setting up and defining the USF file
• Using the Midas Safety Platform to create functional safety reports, and
• Midas integration with the Genus  Synthesis Solution, Innovus  Implementation System, and Conformal Equivalence Checker tools to implement functional safety

The online class is free for all Cadence customers with a Cadence Learning and Support Portal account. If you don’t have a Cadence Support account, go to Registration Help or Register Now and complete the requested information. For instructor-led training sessions "Live" or "Blended" please contact Cadence Training.

Please don't forget to obtain your Digital Badge after completing the training. Add your free digital badge to your email signature or any social media and networking platform to show your qualities and build trust, making you and your projects even more successful.

If you want to make sure you are always the first to know about anything new in training, then you can use the SUBSCRIBE button on the landing page to sign up for our regular training newsletters.

The traditional methods of power analysis lag by various shortcomings and challenges:

• Getting an accurate measure of RTL power consumption during design exploration
• Getting consistent power through the design progress from RTL to P&R.
• System-level verification tools are disconnected from the implementation tools that translate RTL to gates and wires.

The Cadence Joules RTL Power Solution closes this gap by delivering time-based RTL power analysis with system-level runtimes, capacity, and high-quality estimates of gates and wires based on production implementation technology. The Cadence Joules RTL Power Solution is an RTL power analysis tool that provides a unified engine to compute gate netlist power and estimate RTL power. The Joules solution delivers 20X faster time-based RTL power analysis and can analyze multi-million instance designs overnight, with impressive accuracy within 15% of signoff power.

Moreover, it integrates seamlessly with numerous Cadence platforms, eliminating compatibility and correlation issues! In addition, the Joules RTL Power Solution GUI (Graphical User Interface) helps you analyze/debug the power estimation/results using several GUI capabilities.

Want to take a tour of this power estimation world? Gear up to attend the training class created just for you to dive deep into the entire flow and explore this exciting power estimation method/flow with hands-on labs in two days!

Training

In the Joules Power Calculator Training course, you will identify solutions and features for RTL power using Cadence Joules RTL Power Solution. You will set up and run the RTL power flow with Joules RTL Power Solution and identify Joules's Graphical User Interface (GUI) capabilities. The training also explores how you can estimate power using vectorless power, stimulus flow, RTL Stim to Gate flow, and replay flow, and also interfaces Joules with Cadence's Palladium Emulation Platform. You will estimate power at the chip level and understand how to navigate the design and data mining using Joules.

The training also covers power exploration features and how to analyze ideal power and ODC-driven sequential clock gating. You will identify low-activity registers at the clock gate. You will also identify techniques to analyze power, generate various reports, and analyze results through Joules GUI. The training covers multiple strategies to debug low stimulus annotation and how you can better correlate RTL power with signoff. You also identify Genus-Joules Integration. In addition, we ensure that your learning journey is smooth with hands-on labs covering various design scenarios.

Lab Videos

To start you on your exciting journey as an RTL power analysis expert, we have created a series of short channel lab videos on our Customer Support site: Lab Demo: Setting Up and Running Basic RTL Power Flow in Joules RTL Power Solution (Video). You can refer to each lab module's instructions in demo format. This will help accelerate your tool ramp-up and help you perform the lab steps more quickly if you are stuck. You might be a beginner in the RTL power analysis world, but we can help you sail through it smoothly.

What's Next?

Grab your badge after finishing the training and flaunt your expertise!

Related Training

• Genus Low-Power Synthesis Flow with IEEE 1801
• Low-Power Synthesis Flow with Genus Stylus Common UI

Related Blogs

• Do You Want to Flaunt Your Expertise? Grab the Digital Badge Today!
• Become Cadence Certified
• Let's Replay the Process of Power Estimation with the Power of 'x'
• Let's Discover the Secret to Enhance Design's PPAC in a Single Cockpit
• What's Inside Joules Graphical User Interface
• Joules – Power Exploration Capabilities

The Cadence Cerebrus Intelligent Chip Explorer is a revolutionary, machine learning-driven, automated approach to chip design flow optimization. Block engineers specify the design goals, and Cadence Cerebrus will intelligently optimize the Cadence digital full flow to meet the power, performance, and area (PPA) goals in a completely automated way. Use Cerebrus Apps to optimize some aspects of the design as well.

Running a full RTL to GDSII flow, Cadence Cerebrus has a lot of possibilities and combinations of different tool settings to explore.

Using the knowledge from previous runs, combined with on-the-fly analysis within the flow, Cadence Cerebrus can assess many settings combinations and fine-tune the flow accordingly in a very efficient manner.

As technology advances, projects become bigger and way more complex than before. The ability of a single engineer to run simultaneously a large number of blocks in a traditional way is limited. Cadence Cerebrus allows a single engineer to work more efficiently and implement more blocks, while maintaining the same or even better PPA, using compute power.

Being such a revolutionary tool, integrating Cerebrus into your existing flow is surprisingly simple as it can wrap around any existing flow scripts.

Please join me in this course, to learn about the features and basics of Cadence Cerebrus Intelligent Chip Explorer.

We’ll walk through the tool setting stage, explain what is a primitive and how it effects our run, talk about the cost function and the run goals.

We’ll understand the concept of scenarios, learn how to analyze the results of the different runs, and compare them.

In addition, we’ll talk about basic debug rules and methods to analyze failures.

Sounds Interesting?

Please join our “live” one-day Cadence Cerebrus Intelligent Chip Explorer Training @Cadence Feldkirchen planned for October 9th, 2024!

For more details and registration, please contact Training Germany.

If you would like to have an instructor-led training session in another region please contact your local training department.

Become Cadence Certified

Cadence Training Services offers a digital badge for this training course. This badge indicates proficiency in a certain technology or skill and gives you a way to validate your expertise to managers and potential employers. You can highlight your expertise by adding this digital badge to your email signature or any social media platform, such as Facebook or LinkedIn.

Related Training

Innovus Block Implementation with Stylus Common UI

Related Training Bytes

Cerebrus Primitives (Video) 

How to Reuse Cerebrus (Video) 

Cerebrus - Verifying Distribution Script (Video)

How to distribute Cerebrus Scenarios (Video) 

Cerebrus Web Interface Monitor and Control (Video) 

How to Setup Cerebrus for a Successful Run (Video) 

Flow Wrapping: The Cadence Cerebrus Intelligent Chip Explorer Must Have (Webinar) (Video) 

Cerebrus Cost Functions (Video) 

Related Blogs

Training Insights: Cadence Cerebrus Webinar Recording Now Available!

Keep Up with the Revolution—Cadence Cerebrus Training

New to Equivalence Checking? Restart from the Basic Concepts

Training Insights - Free Online Courses on Cadence Learning and Support Portal

Training Insights – Important Facts You Should know About Our Cadence Learning and Support Portal

In an era of abundant and constantly evolving information, the challenge is not just accessing knowledge but understanding and applying it effectively. AI is a transformative technology that is reshaping how we learn, work, and grow. In this blog, we’ll explore how AI accelerates our knowledge acquisition and understand how it can relate to the process of learning, which connects with our daily lives.

The role of AI is to accelerate knowledge by personalizing learning experiences, providing instant access to information, and offering data-driven insights. AI empowers us to learn more efficiently and effectively in many ways. I won't go into much detail, as we are already busy searching for the meaning of AI and what it can do; however, I want to share one inspiring fact about AI. It can analyze vast amounts of data in seconds, making sense of complex information and providing instantaneous actionable insights or concise answers. I understand that humans are looking to speed up things, which can help us understand technology better and perform our tasks faster.

The main reason AI is in focus is because of its ability to perform tasks faster than ever. We aim to enhance the performance of all our products, including the everyday household electronic items we use. Similarly, are we striving to accelerate the learning process? I am committed to assisting you, and one such method is concise, short (minute-long) videos.

In today's fast-paced world, where attention spans are shorter than ever, the rise of social media platforms has made it easier for anyone to create and share short videos. This is where minute videos come in. These bite-sized clips offer a quick and engaging way to deliver information to the audience with a significant impact. Understanding the definitions of technical terms in VLSI Design can often be accomplished in just a minute.

Below are the definitions of the essential stages in the RTL2GDSII Flow. For further reference, these definitions are also accessible on YouTube.

Want to Learn More?

The Cadence RTL-to-GDSII Flow training is available as both "Blended" and "Live" Please reach out to Cadence Training for further information.

And don't forget to obtain your Digital Badge after completing the training!

• You can check out a free Online Version of the training above, which is available 24/7 for all customers with a Cadence Learning ans Support Portal
• You will also have access to our Training Byte Library then which is full of hundres of troubleshooting videos, like the following: What is Digital Implementation?
• You can find more instructions how to get the best out of the Portal in this blog.
• If you would like to stay up-to-date with the latest news and information about Cadence trainings and webinars, subscribe to the Cadence Training emails.

Related Blogs

Training Insights – Why Is RTL Translated into Gate-Level Netlist?

Did You Miss the RTL-to-GDSII Webinar? No Worries, the Recording Is Available!

It’s the Digital Era; Why Not Showcase Your Brand Through a Digital Badge!

Binge on Chip Design Concepts this Weekend!

A more detailed look at fDi's judges’ top five American Cities of the Future 2019/20 for FDI strategy. Naomi Davies reports.

London has been named fDi’s inaugural Fintech Location of the Future for 2019/20, followed by Singapore and Belfast. 

Dr Samir Hamrouni, CEO of the World Free Zones Organization, outlines the attributes that are essential to flourishing free zones.

Research by fDi Intelligence reveals which cities received the most tech start-up FDI relative to their population between 2016 and 2018, with European cities coming out on top.

Australia tops the FDI Strategy category of fDi's Tourism Locations of the Future 2019/20 rankings, followed by Costa Rica and Azerbaijan.

Lithuania's Go Vilnius has been named fDi’s IPA of the Year for 2019, and organisations from across the globe are commended for their investment promotion and economic development activities. 

Egypt became the ‘bread basket’ of Africa in 2018, attracting the largest number of foreign investments in food manufacturing. 

Sub-Saharan Africa is the world’s fastest growing mobile phone market, but how can telecoms companies make the most of the huge opportunities the region provides?

Emerging states must re-orientate their investment efforts to increasingly target those with an outsized social impact

Atlantis in South Africa has a new SEZ focused on green manufacturing, which is hoping to turn around the area's fortunes. Annie Hessler reports.

London is crowned best major city in Europe in fDi's FDI Strategy category, with Glasgow, Vilnius, Reykjavik and Galway also winning out.

North Rhine-Westphalia is fDi's top large region for FDI Strategy, with the Basque Country topping the table for mid-sized regions and Ireland South East first among small regions. 

From historically underperforming when compared with its peers, the German federal state of Rhineland-Palatinate is now attracting major investment projects on the back of its auto and electrification expertise.