A constraint is a user-defined property, or a rule, applied to a physical object, such as a net, pin, or via in a design. There are a number of constraints that can be applied to an object based on its type and behavior. For example, you can define t...(read more)

The Allegro PCB Editor Basic Techniques course provides all the essential training required to start working with Allegro® PCB Editor. The course covers all the design tasks, including padstack and symbol creation, logic import, constraints setup...(read more)

Dear All,

To design an outphasing combiner, I need to extract the input impedances when the circuit is driven by two sources concurrently with a varying phase-shift and plot them on a Smith Chart. However, I can't find a way to display the simulated S-parameters on a Smith Chart.

The testbench, shown below, consists of two sources set to 50 Ohm with variable phase (PORT0: theta, PORT1: -theta) swept from -90° to 90°. The NPORTs are couplers used to isolate the forward and reflected power at each source, i.e. the S-parameters are:

• S13 = S31 = 1; through path
• S21 = S41 = 1; forward and reflected power
• All other are zero

The testbench is simulated with an "hb" analysis instead of "sp", as the two sources have to be excited simultaneously with varying phase-shift to see their load-modulation effect. The sweep is setup in the "Choosing Analysis" window. The powers of the forward (pXa) and reflected (pXb) waves are found through the "Direct Plot" window, e.g. pvr('hb "/p1a" 0 50.0 '(1)) as the power for p1a, and named P1A_Watt. The S-parameters are then calculated as the reflected power w.r.t. the forward power P1B_Watt/P1A_Watt. This approach is based on a Hot S-parameter testbench from ADS.

At this point I would like to display these S-parameters on a Smith Chart. However, this seemed more challenging than expected. One straightforward method would seem to create an empty Smith Chart window in the Display Window and dragging the S-parameters from the rectangular plot on it, but this just deletes them from the Display Window. Hence my question:

How can I display these S-parameters on a Smith Chart?

Dear all,

Hi!

I'm trying to do a Harmonic Balance (HB) Large-Signal S-Parameter (LSSP) simulation to figure out the input impedance of a nonlinear circuit.

Through this simulation, what I want to know is the large-signal S11 only (not S12, S21 and S22).

So, I have simulated with only single port (PORT0) at input, but LSSP simulation is terminated and output log shows following text.

" Analysis `hb' was terminated prematurely due to an error "

The LSSP simulation does not proceed without second port.

Should I use floating second port (which is not necessary for my circuit) to succeed the LSSP simulation?

Does the LSSP simulation really need two ports?

Below figure is my HB LSSP simulation setup.

Additionally, Periodic S-Parameter (PSP) simulation using HB is succeeded with only single port.

What is the difference between PSP and LSSP simulations?

Hi,

My Virtuoso and Spectre Version: ICADVM20.1-64b.NYISR30.2

I have an expression where the EvalType is "sweeps". Here is the expression (I also attached the snapshot):

(peakToPeak(leafValue(swapSweep(delay(?wf1 clip((VT("/clk0") - VT("/clk180")) (VAR("mt_stop") - (4.0 / VAR("datarate"))) VAR("mt_stop")) ?value1 0 ?edge1 "rising" ?nth1 1 ?td1 0 ?tol1 nil ?wf2 clip((VT("/tx_padp") - VT("/tx_padn")) (VAR("mt_stop") - (4.0 / VAR("datarate"))) VAR("mt_stop")) ?value2 0 ?edge2 "rising" ?nth2 1 ?tol2 nil ?td2 nil ?stop nil ?multiple nil) "VDD_FIXED_NOISE") "VREGLN_cmode" 0.85 "VREGDRV_novn" 0.4 "datarate" 1.658e+10) ?overall t) / 10.0)

What this expression does is that it compares the delay between the output data with respect to a reference clock. I then get this information for two conditions (VDD_FIXED_NOISE = 0 or 10mV) to get the effect of the supply-induced jitter. In the expression, I need to give the value of each parameter in different modes to distinguish them from each other. Now I want to sweep the base supply values and see the supply variation effects. For example, I want to change VREGLN_cmode from 0.85 to 0.81 and see how my supply-induced jitter changes. For that, the hard way is to copy the expression and change that value accordingly (e.g. "VREGLN_cmode" 0.81). I'm looking for an easier way to use a variable in the expression. Something like VAR("VREGLN_Sweep"). But I see it doesn't work in my expression and it gives an eVal error. I tested this before in other expressions (not sweep type) and it always worked. I have only one test and these variables are all Design Variables and not Global variables.
I want to know what mistake am I doing here and is there a way to make this work. Sorry that if I could not explain better my inquiry. Thank you.

Hi,

In our design team, we're looking for a strategy to make all cell views self-contained. We are struggling to do so when nport devices are involved.

The nport file requires a full path, whereas what we need is a relative path to the current path of the cell in which we're using the nport.

I have browsed through the forums & cadence support pages, but could not find a solution.

1) There is a proposal from Andrew to add the file directory in ADE option "Simulation Files." :https://community.cadence.com/cadence_technology_forums/f/rf-design/27167/s-parameter-datafile-path-in-nport . This, however, is not suitable, because the cell is not self contained.

2) The new cadence version off DataSource "cellView" in nport options:

This however is not suitable for us due to two reasons:

i- Somehow we don't get this option in the nport cell (perhaps some custom modification from our PDK team)

ii- Even if we had this option, it requires to select the library, which again makes it unsuitable: We often copy design libraries for derivative products using "Hierarchical Copy" feature. And when the library is copied, the nport will still be pointing to the old library. Thus, it is still not self-contained.

In principle, it should not be difficult (technically) to point to a text file relative to the cell directory (f.ex we can make a folder under the same cell with name "sparFiles" & place all spar files under this folder), however it does not seem to be possible.

Could you perhaps recommend us a work-around to achieve our goal: making the cells which contain nport devices self-contained so that when we copy a cell, we do not have to update all the nport file destinations ?

Thanks in advance.

My Cadence Version: IC23.1-64b.ISR4.51

My Spectre version: 23.1.0.362.isr5

I want to plot the inductance through formula L1=(imag(Z(1,1))/(2*pi*freq)), but the system tells me that the freq is unbound variable? What can I do?

While adding an element created from a netlist file in AWR, I am getting the error 'The element type being dropped is not compatible with the window it is being dropped into'. The netlist file in AWR has the following contents:

.subckt BFG520W base collector emitter npn
.model BFG520W NPN(IS=1.016E-15 NF=1.000 BF=220.1 IKF=510E-3 VAF=48.06
+ ISE=2.83E-13 NE=2.035 NR=0.988 BR=100.7 IKR=2.352E-3
+ VAR=1.692 ISC=24.48E-18 NC=1.022 RB=10.00 RE=0.7753
+ RC=2.21 CJC=447.6E-15 MJC=0.07 VJC=0.1892
+ CJE=1.245E-12 TF=8.616E-12 TR=5.437E-12 mfg=NXP)

I have attached screenshots of the element BFG520W2 created due to the above netlist and the error I am getting while adding this element.

Hi everyone,

I'm currently working on my thesis, which involves a beamformer system using CMOS 65nm technology. I'm trying to use the EMX tool for EM simulation but have encountered a few problems. Before diving into my questions about EMX, let me briefly explain how I conduct EM simulations with other software (ADS).

In ADS, I use the EM simulator with the Momentum microwave engine. However, my EM layout is quite large, and the mesh generated is extremely detailed, making it difficult to simulate the entire system. As a workaround, I divide the system into smaller parts and simulate each one individually. I've attached a snapshot of my setup, which includes an amplifier and a 1-to-2 Wilkinson power divider. I've separated these circuits and placed pins to facilitate EM simulations for each. I also placed ground pins at the boundaries of each circuit to connect them to the ground plane.

Here’s the link to the image (I'm unable to upload it due to an error): https://drive.google.com/file/d/13Qn4-DvMBj_K1JQLXrTWaWZ8uaLJr15u/view?usp=sharing

Now, moving on to EMX (version 6.3). For a maximum frequency of 31 GHz, I set the edge mesh = thickness = 0.4 µm (approximately the skin depth). However, when I simulate the circuit (amplifier + divider), the mesh on the ground plane becomes very dense, which makes running the simulation impossible due to excessive memory requirements. I reverted to my ADS approach and divided the circuit into two parts, placing ports to connect them. Unfortunately, EMX doesn't allow me to place multiple edge ports on the same edge for the ground plane, which has left me confused. Here are a couple of questions I have:

1. Is breaking the circuit into smaller parts a valid approach? Given the large ground plane, the mesh size for the ground is significant, making simulations challenging. Are there any methods to manage this issue?

2. Regarding the ground pins, why can't I place multiple edge ports to connect the ground planes of both circuits as I did in ADS? If this approach is incorrect, could you suggest alternative methods for simulating individual circuits and connecting them to estimate system performance?

Any insights would be greatly appreciated. Thank you in advance for your help!

Hi I noticed that some figures from the old posts in the cadence blogs have been missing.

I think this problem happened before and Andrew Beckett asked the original author to fix the issue:

 Figures missing in the RF Design Blogs article of "Measuring Fmax for MOS Transistors" 

Some of these posts are quite valuable, and would be nice to have access to the figures, which are a very important part of some posts,

Thanks

Leandro

An AMS Designer Flex simulation gives you the most immediate access to the latest simulation technology on either side, gets out of the way of the core engines and allows the engine performance to shine while providing access to new features. Check out this blog to know more.

Che(read more)

This blog introduces you to an efficient way to debug interface elements or connect modules in a mixed-signal simulation.(read more)

Read this blog for an overview to the Circuit physical verification and parasitic extraction design stage in the Custom IC Design methodology and the key design steps which can help you achieve this.(read more)

Designing 3D-ICs with integrity involves a commitment to ethical practices, reliability, and sustainability throughout the design and manufacturing process. This includes using environmentally friendly materials, ensuring robust and efficient performance, and incorporating thorough testing and verification. By prioritizing transparency, responsibility, and long-term sustainability, designers can create advanced integrated circuits that meet high standards of quality and social responsibility.

Start Learning Now!

Start with our Designing with Integrity 3D-IC online course, which introduces Integrity 3D-IC, the industry's first comprehensive, high-capacity 3D-IC platform that integrates 3D design planning, implementation, and system analysis in a single, unified environment. You will be guided through the following activities involved in designing a silicon interposer with a digital ASIC and HBM2 interface in a 2.5D configuration.

• You will design the interposer from scratch in the new Integrity System Planner and the Integrity 3D-IC implementation environment.
• You will examine the ASIC and interposer designs using some of the new 3D-IC multi-die design features.
• You will route the interposer using some of the new advanced routing capabilities with NanoRoute

—and this in only two days!

WATCH VIDEO

Interested? Get an overview in less than two minutes.

Are you primarily interested in selected snippets instead? Then, take our Training Bytes, which—like the online training course—are available to Cadence customers for free 24/7 in the Cadence Learning and Support portal.

Cadence Training Services now offers free Digital Badges for all popular online training courses. These badges indicate proficiency in a certain technology or skill and give you a way to validate your expertise to managers and potential employers. You can add the digital badge to your email signature or any social media channels, such as Facebook or LinkedIn, to highlight your expertise.

To find out more, see the blog post. It’s the Digital Era; Why Not Showcase Your Brand Through a Digital Badge!

Related Resources

• 3D-IC Introduction (Video)
• 3D-IC Development Process With Challenges. (Video)
• Demo: How to Create the Interposer Contact Pads and Die Connectivity Using the Integrity 3D-IC? (Video)
• Demo: How To Pull The Interposer Design From System Planner Into Integrity 3D-IC Layout? (Video)
• Demo: Routing The Interposer Design Using The Integrity 3D-IC Layout_Part 1 (Video)
• Demo: Routing The Interposer Design Using The Integrity 3D-IC Layout_Part 2 (Video)
• Demo: How To Create C4 Bumps For NC Connections And Generating C4 Dummy Cover Bumps In Integrity 3D-IC? (Video)

Related Blogs

• How Cadence Is Expanding Innovation for 3D-IC Design
• Training Bytes: They May Be Shorter, But the Impact Is Stronger!
• Training Insights — 3D-IC: What Is Silicon Interposer?
• System Analysis Knowledge Bytes: What’s New in the Clarity 3D Solver Course
• System Analysis Knowledge Bytes - Early System-Level Thermal Analysis
• 3D-IC: The Future of Integrated Electronics Is the Future of Electronics Itself

Related Trainings

• OrbitIO System Planner
• Allegro Package Designer Plus

In this training webinar, we explore the concepts of RTL design, design verification, and coverage analysis while unveiling the exciting world of front-end design flow. We will guide you through the essential steps in creating integrated circuits, the building blocks of modern electronics.

We’ll break down the process into manageable stages, from defining the chip’s functionality to its physical realization. We’ll investigate the front-end part of the RTL-to-GDSII flow—from specification to functional verification and design coverage—and explore:

• Key concepts of specifying chip behavior and performance
• How to translate ideas into a digital blueprint and transform that into a design
• How to ensure your design is free of errors

This webinar provides practical knowledge, making it your gateway to understanding the magic behind RTL-to-GDSII front-end design flow.

When Is the Webinar?

Date and Time

Wednesday, September 18, 2024
07:00 PDT San Jose / 10:00 EDT New York / 15:00 BST London / 16:00 CEST Munich / 17:00 IDT Jerusalem / 19:30 IST Bangalore / 22:00 CST Beijing 

REGISTER

To register for this webinar, sign in with your Cadence Support account (email ID and password) to log in to the Learning and Support System.

Then select Enroll to register for the session. Once registered, you’ll receive a confirmation email containing all login details.

If you don’t have a Cadence Support account, go to Cadence User Registration and complete the requested information. Or visit Registration Help.

For inquiries or issues with registration, reach out to eur_training@cadence.com.

For inquiries or issues with registration, reach out to eur_training@cadence.com.

To view our complete training offerings, visit the Cadence Training website.

Want to share this and other great Cadence learning opportunities with someone else? Tell them to subscribe.

Want to Learn More?

This link gives you more information about the related training course and a link to enroll:

Cadence RTL-to-GDSII Flow Training

The course includes slides with audio and downloadable laboratory exercises designed to emphasize the topics covered in the lecture. There is also a Digital Badge available for the training.

The online class is free for all Cadence customers with a Cadence Learning and Support Portal account. For instructor-led training sessions "Live" or "Blended" please contact Cadence Training.

Also, take this opportunity to register for the free Online Trainings related to this webinar topic.

Cadence RTL-to-GDSII Flow

Xcelium Simulator

Verilog Language and Application

Xcelium Integrated Coverage

Related Training Bytes

How to Run the Synthesis Without DFT?

How to Run the Synthesis Flow with DFT? (Video)

Related Blogs

Did You Miss the RTL-to-GDSII Webinar? No Worries, the Recording Is Available!

Training Insights – Why Is RTL Translated into Gate-Level Netlist?

Training Bytes: They May Be Shorter, But the Impact Is Stronger!

Cadence Support - A Round-the-Clock Problem Solver, Webinar Recording Available!

Power efficiency is a critical factor in the fast-evolving world of semiconductor design.

The IEEE 1801 standard, also known as UPF (Unified Power Format), was developed by the IEEE to address the intricate challenges associated with power management in contemporary semiconductor designs. This standard offers a uniform framework for defining power domains, power states, and power intent, ensuring consistency across diverse tools and phases of the design process. By utilizing UPF, you can precisely model and regulate power consumption, a critical aspect for battery-operated devices, high-performance computing, and energy-efficient designs.

The key concepts of IEEE 1801 are:

1. Power domains
2. Power states
3. Power gating and isolation
4. Power switches
5. Level shifters, isolation, and retention cells
6. Macro model

Based on these building blocks, you write the power intent of the design.

The power intent for the design includes identifying/implementing low-power strategies that provide a clear description of the power architecture of a design.

The power definitions can effectively manage power consumption and ensure the chip meets its power and performance requirements.

You can start by creating the Power Supply Network, which defines how power is supplied to the design's various power domains and logic cells.

What's the next step to build the file? How do you understand the various concepts related to IEEE 1801? How do you complete the rest of the power intent file?

Relax!

Gear up to attend the training class created just for you to dive deep into the entire format and explore this exciting power specification method/format with hands-on labs in one day!

Training

Fundamentals of IEEE 1801 Low-Power Specification Format Training

This course is a complete tutorial for understanding the fundamentals of IEEE 1801 low-power specification format concepts. You learn about IEEE 1801 power supply networks, ground ports and nets, creating and connecting supply ports/nets, power domain, power switch, power states, defining isolation and level shifter strategies, hierarchical IEEE 1801, and various versions of the IEEE 1801. You also explore how power intent information can be used for a design across various flow stages, such as functional verification, synthesis, logic equivalency checking, place-and-route, test, timing signoff, power integrity, and so forth, using Cadence^® tools.

Labs

We ensure that your learning journey is smooth with hands-on labs covering various design scenarios.

Lab Videos

Now, the exciting part is that to help you further, we have created engaging videos of the training labs. You can refer to the lab module's instructions in demo format at https://support.cadence.com.

Lab Demo: Checking Power Supply Network in IEEE 1801 format and Running IEEE 1801 Quality Checks using Conformal Low Power

Lab Demo: Checking Power Intent for The Macro Connections in IEEE 1801 Format And Running IEEE 1801 Quality Checks using Conformal Low Power 

Online Class

Here is the course link.

Get ready for the most thrilling experience with Accelerated Learning!

The more you know, the faster you go!

Grab the cycle  or hike it, based on your existing knowledge.

Take the quiz and increase your learning pace!!

What's Next?

Grab your Badge after finishing the training and flaunt the expertise you have built up. 😊

Ready to take a tour of this power specification world? Let's help you enroll in this course.

We organize this training for you as a "Blended" or "Live" training. Please reach out to Cadence Training for further information. If you want to ensure you are always the first to know about anything new in training, you can use the SUBSCRIBE button on the landing page to sign up for our regular training newsletters.

Related Short Training Bytes/Videos

Enhance the learning experience with short videos:

Genus Synthesis Solution: Video Library

 Joules RTL Power Solution: Video Library

Related Training

 Low-Power Synthesis Flow with Genus Synthesis Solution

Genus Low-Power Synthesis Flow with IEEE 1801

Related Blogs

It's the Digital Era; Why Not Showcase Your Brand Through a Digital Badge! - Digital Design - Cadence Blogs - Cadence Community

Relax in Summer with Cooler IC chips and Ice-Cream! Do you want to Explore the Recipe? - Digital Design - Cadence Blogs - Cadence Community

Power Is HOT and Touches Everything and Everybody! But the Challenge Is To Deal With Low Power During Design Synthesis; How? - Digital Design - Cadence Blogs - Cadence Community

Binge on Chip Design Concepts this Weekend! - Digital Design - Cadence Blogs - Cadence Community

The Cadence Cerebrus Intelligent Chip Explorer is a revolutionary, machine learning-driven, automated approach to chip design flow optimization. Block engineers specify the design goals, and Cadence Cerebrus will intelligently optimize the Cadence digital full flow to meet the power, performance, and area (PPA) goals in a completely automated way. Use Cerebrus Apps to optimize some aspects of the design as well.

Running a full RTL to GDSII flow, Cadence Cerebrus has a lot of possibilities and combinations of different tool settings to explore.

Using the knowledge from previous runs, combined with on-the-fly analysis within the flow, Cadence Cerebrus can assess many settings combinations and fine-tune the flow accordingly in a very efficient manner.

As technology advances, projects become bigger and way more complex than before. The ability of a single engineer to run simultaneously a large number of blocks in a traditional way is limited. Cadence Cerebrus allows a single engineer to work more efficiently and implement more blocks, while maintaining the same or even better PPA, using compute power.

Being such a revolutionary tool, integrating Cerebrus into your existing flow is surprisingly simple as it can wrap around any existing flow scripts.

Please join me in this course, to learn about the features and basics of Cadence Cerebrus Intelligent Chip Explorer.

We’ll walk through the tool setting stage, explain what is a primitive and how it effects our run, talk about the cost function and the run goals.

We’ll understand the concept of scenarios, learn how to analyze the results of the different runs, and compare them.

In addition, we’ll talk about basic debug rules and methods to analyze failures.

Sounds Interesting?

Please join our “live” one-day Cadence Cerebrus Intelligent Chip Explorer Training @Cadence Feldkirchen planned for October 9th, 2024!

For more details and registration, please contact Training Germany.

If you would like to have an instructor-led training session in another region please contact your local training department.

Become Cadence Certified

Cadence Training Services offers a digital badge for this training course. This badge indicates proficiency in a certain technology or skill and gives you a way to validate your expertise to managers and potential employers. You can highlight your expertise by adding this digital badge to your email signature or any social media platform, such as Facebook or LinkedIn.

Related Training

Innovus Block Implementation with Stylus Common UI

Related Training Bytes

Cerebrus Primitives (Video) 

How to Reuse Cerebrus (Video) 

Cerebrus - Verifying Distribution Script (Video)

How to distribute Cerebrus Scenarios (Video) 

Cerebrus Web Interface Monitor and Control (Video) 

How to Setup Cerebrus for a Successful Run (Video) 

Flow Wrapping: The Cadence Cerebrus Intelligent Chip Explorer Must Have (Webinar) (Video) 

Cerebrus Cost Functions (Video) 

Related Blogs

Training Insights: Cadence Cerebrus Webinar Recording Now Available!

Keep Up with the Revolution—Cadence Cerebrus Training

New to Equivalence Checking? Restart from the Basic Concepts

Training Insights - Free Online Courses on Cadence Learning and Support Portal

Training Insights – Important Facts You Should know About Our Cadence Learning and Support Portal

In an era of abundant and constantly evolving information, the challenge is not just accessing knowledge but understanding and applying it effectively. AI is a transformative technology that is reshaping how we learn, work, and grow. In this blog, we’ll explore how AI accelerates our knowledge acquisition and understand how it can relate to the process of learning, which connects with our daily lives.

The role of AI is to accelerate knowledge by personalizing learning experiences, providing instant access to information, and offering data-driven insights. AI empowers us to learn more efficiently and effectively in many ways. I won't go into much detail, as we are already busy searching for the meaning of AI and what it can do; however, I want to share one inspiring fact about AI. It can analyze vast amounts of data in seconds, making sense of complex information and providing instantaneous actionable insights or concise answers. I understand that humans are looking to speed up things, which can help us understand technology better and perform our tasks faster.

The main reason AI is in focus is because of its ability to perform tasks faster than ever. We aim to enhance the performance of all our products, including the everyday household electronic items we use. Similarly, are we striving to accelerate the learning process? I am committed to assisting you, and one such method is concise, short (minute-long) videos.

In today's fast-paced world, where attention spans are shorter than ever, the rise of social media platforms has made it easier for anyone to create and share short videos. This is where minute videos come in. These bite-sized clips offer a quick and engaging way to deliver information to the audience with a significant impact. Understanding the definitions of technical terms in VLSI Design can often be accomplished in just a minute.

Below are the definitions of the essential stages in the RTL2GDSII Flow. For further reference, these definitions are also accessible on YouTube.

Want to Learn More?

The Cadence RTL-to-GDSII Flow training is available as both "Blended" and "Live" Please reach out to Cadence Training for further information.

And don't forget to obtain your Digital Badge after completing the training!

• You can check out a free Online Version of the training above, which is available 24/7 for all customers with a Cadence Learning ans Support Portal
• You will also have access to our Training Byte Library then which is full of hundres of troubleshooting videos, like the following: What is Digital Implementation?
• You can find more instructions how to get the best out of the Portal in this blog.
• If you would like to stay up-to-date with the latest news and information about Cadence trainings and webinars, subscribe to the Cadence Training emails.

Related Blogs

Training Insights – Why Is RTL Translated into Gate-Level Netlist?

Did You Miss the RTL-to-GDSII Webinar? No Worries, the Recording Is Available!

It’s the Digital Era; Why Not Showcase Your Brand Through a Digital Badge!

Binge on Chip Design Concepts this Weekend!

In this recent Training Webinar, we explore the concepts of RTL design, design verification, and coverage analysis while unveiling the exciting world of front-end design flow by guiding you through essential steps involved in creating integrated circuits—the building blocks of modern electronics.

We’ll break down the process into manageable stages, from defining the chip’s functionality to its physical realization. We’ll investigate the front-end part of the RTL-to-GDSII flow—from specification to functional verification and design coverage—and explore:

• Key concepts of specifying chip behavior and performance
• How to translate ideas into a digital blueprint and transform that into a design
• How to ensure your design is free of errors

Watch the Training Webinar recording from September 18, 2024: A Beginner’s Guide to RTL-to-GDSII Front-End Flow

Want to Learn More?

This link gives you more information about this RTL-to-GDSII Flow, the related training course, and a link to enroll:

Cadence RTL-to-GDSII Flow Training

The course includes slides with audio and downloadable laboratory exercises designed to emphasize the topics covered in the lecture. There is also a Digital Badge available for the training.

 Also, take this opportunity to register for the free Online Training related to this Webinar Topic.

Cadence RTL-to-GDSII Flow

Xcelium Simulator

Verilog Language and Application

Learning Maps

The online class is free for all Cadence customers with a Cadence Learning and Support Portal account. For instructor-led training sessions "Live" or "Blended" please contact Cadence Training.

Related Training Bytes

What is RTL Coding In VLSI Design?

What is Digital Verification?

What Is Synthesis in VLSI Design?

What Is Logic Equivalence Checking in VLSI Design?

What Is DFT in VLSI Design?

What is Digital Implementation?

What is Power Planning?

What are DRC and LVS in Physical Verification?

What are On-Chip Variations?

Related Blogs

Did You Miss the RTL-to-GDSII Webinar? No Worries, the Recording Is Available!

Training Insights – Why Is RTL Translated into Gate-Level Netlist?

Training Bytes: They May Be Shorter, But the Impact Is Stronger!

Cadence Support - A Round-the-Clock Problem Solver, Webinar Recording Available!

In the era of Artificial Intelligence, front-end designers need a magical key to empower them with technology that enables fully optimized RTL for implementation handoff and provides RTL designers with capabilities to accurately assist in the implementation convergence process.

The magic lies with Cadence Joules RTL Design Studio, an expert system that leverages generative AI for RTL design exploration, triages possible causes of violations, and additional insights that empower designers to understand how to address issues in their RTL, leading to smarter and more efficient chip design.

This unlocks the immense debugging and design analysis capabilities from a single, unified cockpit, enabling fully optimized RTL design prior to implementation handoff for the front-end designers and addresses all aspects of physical design by adding visibility into power, performance, area, and congestion (PPAC)

One critical component is the clock tree, which distributes the clock signal to all sequential elements, such as flip-flops and latches. Designers need the right techniques in the beginning stage to optimize the clock tree structure, ensuring that their designs meet the required timing specifications, reduce power consumption, maintain signal integrity, and increase reliability.

 This incredible feature is part of the Joules RTL Design Studio.

How do you efficiently explore the clock tree structure to optimize the results using Joules RTL Design Studio?

Joules Studio allows viewing a simplified version of the clock structure. This feature is primarily designed to help display clock frequency scaling through clock dividers. You can customize colors, symbols, and design elements using an input file. Additionally, you can cross-probe the custom clock tree structure to other widgets and the main schematic view in Joules Studio.

Moreover, with the clock tree preference features of the ideal clock tree wizard in Joules Studio GUI, you can highlight clock path, generate clocks and master clock, set case analysis, fold and unfold instances, undo and redo, set sense and disable timing, color preference, etc.

You can binge on these features through the channel videos posted on the support portal, which covers the Joules RTL Design Studio GUI Clock Tree Structure and Features of Ideal Clock Tree Wizard.

You can refer to the videos on Cadence Online Support (Cadence login required).

​Video Links:
Viewing Custom Clock Tree Structure in Joules RTL Design Studio (Video) 

Exploring Clock Tree Preference Widget of Ideal Clock Tree Wizard in Joules RTL Design Studio (Video) 

Want to learn more?

Explore the one-stop solution Joules RTL Design Studio Product Page on Cadence Online Support (Cadence login required).

Related Resources 

Related Training Bytes:

Understanding Prototype Design Flow in Joules RTL Design Studio (Video)

Running Prototype Implementation Flow in Joules RTL Design Studio (Video)

Understanding Analyze Timing By Hierarchy In Joules RTL Design Studio (Video)

Related Courses:

• Joules Power Calculator

Want to Enroll in this Course?

We organize this training for you as a "Blended" or "Live" training. Please reach out to Cadence Training for further information.

Please don't forget to obtain your Digital Badge after completing the training.

Related Blogs:

Let's Discover the Secret to Enhance Design's PPAC in a Single Cockpit! - Digital Design - Cadence Blogs - Cadence Community

Joules RTL Design Studio: Accelerating Fully Optimized RTL - Digital Design - Cadence Blogs - Cadence Community

Let's Replay the Process of Power Estimation with the Power of 'x'! - Digital Design - Cadence Blogs - Cadence Community

Is Design Power Estimation Lowering Your Power? Delegate and Relax! - Digital Design - Cadence Blogs - Cadence Community

Russia remains fDi’s most diversified commodity economy, while second ranked Brazil has displaced Ukraine into third place. Cathy Mullan reports.

The UAE's DMCC takes home the top prize in fDi’s Global Free Zones of the Year for a fifth consecutive year. 

Research by fDi Intelligence reveals which cities received the most tech start-up FDI relative to their population between 2016 and 2018, with European cities coming out on top.

Lithuania's Go Vilnius has been named fDi’s IPA of the Year for 2019, and organisations from across the globe are commended for their investment promotion and economic development activities. 

The UK’s prime minister has pledged to rebalance the UK economy away from a dominant London. However, this might require greater incentives for foreign investment in the regions outside of the capital, which are underperforming. 

Paris Region has kept its fDi European Region of the Future title, while Dublin Region holds on to second place and North Rhine-Westphalia is in third. 

From historically underperforming when compared with its peers, the German federal state of Rhineland-Palatinate is now attracting major investment projects on the back of its auto and electrification expertise.

Foreign investment into Serbia is growing at a healthy pace thanks to its attractive automotive manufacturing industry and highly regarded free zones.

Serbia’s technology cluster is gaining momentum and attracting FDI, for both its software and hardware expertise.

Warsaw already offers a skilled workforce and has improved its infrastructure – now it must focus on climate change and reducing congestion, mayor Rafał Trzaskowski tells fDi.

Having opened new production facilities in Rwanda and South Africa, Mara Phones is looking to alter Africa's mindset from being a 'consumer' to being a 'manufacturer'. 

Tesla's decision part of broader trend of investment into Germany at UK's expense.

US web infrastructure and cyber security company Cloudflare wants to improve people’s internet experiences through affordable, reliable and accessible interconnection points, especially in less privileged parts of the world. 

Passion Capital's Eileen Burbidge talks to fDi about what fintech companies should consider when expanding internationally, and why London will always be a key market in the sector.

Financial incentives from two different cities persuaded US grocery chain The Fresh Market to stay headquartered in its home state of North Carolina.

Lower fertility rates will boost economic growth, according to a demographic model developed by Renaissance Capital. 

$73.8m mega-project will be the first of its kind in the city.

Celebrating its centennial, Albania’s capital is ranked among fDi’s top five mid-sized European Cities of the Future 2020/2021 for Cost Effectiveness

Announced greenfield projects into China plummeted in early 2020 with the US and Europe taking the lion's share of global foreign investment. 

Despite recurrent challenges, Afghanistan’s business environment is improving. Now the authorities are working to persuade investors the rewards are worth the risk through a series of economic and legal reforms. 

US-led vetting and certification of big-ticket projects may go a long way to allaying western investor concerns about rule of law and transparency issues, says intelligence firm Alaco’s head of content.

Venture capital funding has reached record levels in recent years, enabling start-ups to expand across borders – but their ability to do this depends on their type of business, and where they are founded.

The global pharmaceutical sector has seen consistent growth since 2014, with western Europe a major beneficiary.

Philomène Dias, director of inward investment at Portuguese investment promotion agency Aicep, on how staff and organisation are working through lockdown.

Eco Equity is one of only a few Europe-based investors in medicinal cannabis from Africa and the Caribbean, an area in which the UK is missing an opportunity, according to CEO Jon-Paul Doran.

The fallout from the pandemic looks set to stall trade and investment to Latin America.

JPMorgan has pledged to push clients towards aligning with the Paris Agreement

Ford's bestselling F-150 full-size pickup truck receives minor changes for the 2025 model year, including some removal of standard equipment on certain trim levels in exchange for lower starting prices. Ford also rolls out BlueCruise 1.4 and expands the availability of the latest iteration of its limited hands-free driving system. The base F-150...

Jeep Wrangler sets the bar for off-roading capability Larger Ford Bronco has a more modern suspension Both SUVs have removable doors and tops When Ford relaunched the Bronco for the 2021 model year, it had one target in its sights: The Jeep Wrangler. The Wrangler has been the American benchmark for off-roading capability in the 80-plus years since...