The process of designing a substation usually begins with the general substation layout, which is dependent on the required safety clearance and insulation withstand, as well as the permissible loads delivered to substation equipment and structures. The permissible loads, in... Read more

The post Good practice in the design of concrete and steel structures in power substations appeared first on EEP - Electrical Engineering Portal.

This technical article we will go through a number of existing applications for conducting a wide range of electrical studies. However, the practice says that studies involving load flow and fault analyses are the most commonly utilized programs in power transmission... Read more

The post Eleven most important calculations you can perform with power system analysis software appeared first on EEP - Electrical Engineering Portal.

Schematic drawings, also known as electrical or circuit diagrams, are essential tools for understanding and designing electrical circuits. Mastering schematic drawing is a fundamental skill for field engineers, allowing them to effectively troubleshoot, maintain, and modify electrical schemes. This technical... Read more

The post Fundamental concepts of schematic drawings for true field engineers (hands on HV schemes) appeared first on EEP - Electrical Engineering Portal.

Welcome to this comprehensive technical article that delves into the intricacies of electrical schematics, shedding light on crucial elements such as loops, wire connections, auxiliary contacts, MCBs, contactors, circuit breakers, isolators, earth switches, and terminal blocks. In the world of... Read more

The post Fundamental concepts of schematic drawings: Going deeper into analysis and design intricacies appeared first on EEP - Electrical Engineering Portal.

In the intricate landscape of electrical engineering, the ability to decipher and interpret schematic drawings is a skill that separates the adept from the novice. This technical article delves into the art of understanding schematics, unraveling the complexities through a... Read more

The post A roadmap for engineers seeking mastery in the language of electrical schematics appeared first on EEP - Electrical Engineering Portal.

The majority of utilities are normally extremely well aware of the economic aspects and savings that can be obtained at all stages of the transformer’s life cycle. This is because the purchase of a transformer involves a very high capital... Read more

The post 11 factors that significantly influence the transformer price (Be careful when specifying) appeared first on EEP - Electrical Engineering Portal.

This technical article discusses the essentials of transformer differential protection and restricted earth fault protection schemes, contrasting the two and elaborating on why the latter is necessary. Furthermore, it reveals the outcomes of stability tests performed on a 502 MVA... Read more

The post Mastering stability test of power transformer: Differential and Restricted Earth Fault (REF) protection appeared first on EEP - Electrical Engineering Portal.

First, let’s say a word or two about the essentials of power distribution systems for our young electrical engineers. An electric distribution system, or distribution plant as it is sometimes called, is all of that part of an electric power... Read more

The post The loop electrical distribution system used to supply bulk loads (industrial plants and buildings) appeared first on EEP - Electrical Engineering Portal.

This technical article provides a collection of the common drawings that are sent by the manufacturer to the client for approval and reference. The goal of these drawings is to verify that the transformers that are going to be manufactured... Read more

The post Contract drawings for a power transformer – The checklist you should always follow appeared first on EEP - Electrical Engineering Portal.

This technical article provides an overview of the various choices and assists electrical engineers in determining the criteria that should be included in the transformer specifications in order to meet the requirements of their particular application. A power plant often... Read more

The post Transformers in plant power distribution: The bigger picture appeared first on EEP - Electrical Engineering Portal.

Electrical systems normally use current and voltage transformers for protection and measurement purposes. They represent the power system’s eyes and ears, and it’s essential to fully understand how they work, how to make the correct specification and most importantly, the... Read more

The post What steps should be taken to avoid choosing the incorrect current and voltage transformers? appeared first on EEP - Electrical Engineering Portal.

Many young engineers consider cement plants pretty complicated because of their weird technology. The reason probably lies in the fact that you cannot understand all those technologies unless you worked in such a plant and saw all processes from scratch.... Read more

The post The essentials of electrical systems in cement plants appeared first on EEP - Electrical Engineering Portal.

Proper analysis of the VFD’s power and control circuit diagrams is essential for successful troubleshooting. But before starting any analysis, you must know how your system connected through VFD works and how it breathes. You must also know all components... Read more

The post Inside Variable Frequency Drive (VFD) Panel: Configuration, Schematics and Troubleshooting appeared first on EEP - Electrical Engineering Portal.

Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up to and including 52 kV Switchgears are important nodal points in modern power distribution. Correspondingly important is their reliable functioning, a clearly defined switching behavior... Read more

The post IEC 62271-200 – HV Switchgear And Controlgear appeared first on EEP - Electrical Engineering Portal.

One of the significant challenges that substation engineers face is justifying substation automation investments. The positive impacts that automation has on operating costs, increased power quality, and reduced outage response are well known. But little attention is paid to how... Read more

The post Advantages Of IEC 61850 appeared first on EEP - Electrical Engineering Portal.

In the design of electrical power systems, the ANSI Standard Device Numbers denote what features a protective device supports (such as a relay or circuit breaker). These types of devices protect electrical systems and components from damage when an unwanted... Read more

The post Protection Relay – ANSI Standards appeared first on EEP - Electrical Engineering Portal.

These standards are the whole of the prescriptions on the basis of which machines, apparatus, materials and the installations should be designed, manufactured and tested so that efficiency and function safety are ensured – and all according to the UK Electrical... Read more

The post UK Electrical Industry British Standards (BS) appeared first on EEP - Electrical Engineering Portal.

The audible sound radiated by transformers is generated by a combination of magnetostrictive deformation of the core and electromagnetic forces in the windings, tank walls and magnetic shields. Historically, the sound generated by the magnetic field inducing longitudinal vibrations in the... Read more

The post An Overview of IEC 60076-10 – Determination Of Sound Levels Of Power Transformers appeared first on EEP - Electrical Engineering Portal.

District heating is a system which provides a number of buildings with heat from a central boiler plant through pre-insulated pipes. Pre-insulated pipes are in fact a modern kind of heat culvert or district heating duct, but since these systems... Read more

The post District heating – Heat from a central boiler plant appeared first on EEP - Electrical Engineering Portal.

Efficiencies of fan systems vary considerably across impeller types. The average energy saving potential in these systems in the U.S. manufacturing industry is estimated at 6%. For optimal savings and performance, it is recommended that a systems approach is used.... Read more

The post Six energy efficiency improvement opportunities in fan systems appeared first on EEP - Electrical Engineering Portal.

At its most basic, Solar Power is the conversion of sunlight into electricity; either directly using photovoltaics (PV), or indirectly using concentrated solar power (CSP). CSP systems use a combination of lenses/mirrors and tracking systems to focus a large area... Read more

The post Solar Panels and Feed-in Tariffs – The Intricacies of Solar Power appeared first on EEP - Electrical Engineering Portal.

The problem of energy accessibility and production on Mars is one of the three main challenges for the upcoming colonisation of the red planet. The energetic potential on its turn is mainly dependent on the astrophysical characteristics of the planet.... Read more

The post Want to live and use energy on Mars? Why not? appeared first on EEP - Electrical Engineering Portal.

– Array Size: 10, 12-volt, 51-watt modules; Isc= 3.25 amps, Voc= 20.7 volts – Batteries: 800 amp-hours at 12 volts – Loads: 5 amps DC and 500-watt inverterwith 90% efficiency. The PV modules are mounted on the roof. Single-conductor cables... Read more

The post Calculation Example of Small Photovoltaic (PV) Residential Stand-Alone System appeared first on EEP - Electrical Engineering Portal.

The present electric grids use the technology of 1970’s. But with the advancement in various concepts of power generation, problems associated with power outages and thefts, and also due to increase in demand, we require a modernized grid to avail... Read more

The post An Overview Of Smart Power Grid appeared first on EEP - Electrical Engineering Portal.

Network planning Power electronics (HVDC/FACTS) Bulk renewable integration Energy Management System (EMS) Smart substation automation and protection Integrated Substation Condition Monitoring (ISCM) Communication Solutions Distribution Management System (DMS) Distribution automation and protection Distributed Energy Resources (DER) Decentralized Energy Management System... Read more

The post Smart Grids and The New Age of Energy appeared first on EEP - Electrical Engineering Portal.

The creation and delivery of power is one basic infrastructure expected by all modern industrial societies. Power distribution basics started in the US in the early 1900s when the first AC grid was established. Since 12 independent power grids were... Read more

The post Comparison of major power grid failures in US and around the world (1) appeared first on EEP - Electrical Engineering Portal.

Continued from first part: Comparison of major grid failures in United States and around the world (part 1) On the International side, about 1/5 of the power outages (9 of 44) were not given a cause in the reports. A... Read more

The post Comparison of major power grid failures in US and around the world (2) appeared first on EEP - Electrical Engineering Portal.

Power utilities use telecommunication systems either as a support for grid assets’ operation or as the enabler for voice communications among operating staff. The main objective of utility telecommunications is to connect remote premises and staff with central premises and... Read more

The post Five telecommunication systems embedded in smart grid applications and services appeared first on EEP - Electrical Engineering Portal.

For the last several decades, every engineering task related to processing control is realized by the use of PLC (Programmable Logic Controller). If we are talking about induction motor control, which is the most common case, usually a VFD (Variable... Read more

The post Learn how to use PLC and VFD for pump control: Power and control circuits analysis appeared first on EEP - Electrical Engineering Portal.

Wastewater pumping stations are very common application examples of three-phase induction motors. There are numerous varieties of power supply and control logic, depending on exact conditions in the place of installation, the role of the pumping station inside a sewer... Read more

The post Design and control considerations for an example of the waste water pumping station appeared first on EEP - Electrical Engineering Portal.

Ambiguous words, delivered with earnest passion, lend special power to "Airline Living." It's the sort of song that's sure to force different meanings onto different people, depending upon their place in life and state of mind.

Hello, hope all is well with you! It’s our pleasure to share with you two Cyber Monday deals for our new electrical engineers, expiring on December 3rd: 20% on EEP Pro Premium Membership and 30% off on all courses and... Read more

The post Your Cyber Monday in EEP! Save Big on Premium Membership and Video Courses appeared first on EEP - Electrical Engineering Portal.

Just a short note from me today, the end of this crazy year. I’d like to wish you a normal and happy New Year on behalf of myself and everyone else at EEP. This year was like no other year... Read more

The post Hey engineers, wish you a happy and normal new year, 2021! appeared first on EEP - Electrical Engineering Portal.

Black Friday is gone, but Cyber Monday is here and it’s getting better! Let us share with you two Cyber Monday deals for our electrical engineers, expiring on December 3rd: 20% off on EEP Pro Premium Membership and 30% off... Read more

The post Cyber Monday in EEP! 30% off on courses and 20% off on premium membership! appeared first on EEP - Electrical Engineering Portal.

Here we are, at the end of 2021, which was extremely intense for all of us. This year will be remembered for many things, but if you ask me, the most impressive was the global loss of common sense, sadly,... Read more

The post Wish you all the strength, courage and clear minds in 2022! appeared first on EEP - Electrical Engineering Portal.

Black Friday is gone, but Cyber Monday is here and it’s getting better! It’s the Last Day!! Let us share with you two Cyber Monday deals for our electrical engineers, expiring on December 1st: 20% off on EEP Pro Premium... Read more

The post Cyber Monday in EEP! 30% off on courses and 20% off on PRO membership plan! appeared first on EEP - Electrical Engineering Portal.

Here we are at the conclusion of 2022, a year that was very stressful for all of us. There are many aspects about this year that will be remembered, but, in my opinion, the same as it was for 2021,... Read more

The post Well engineers, it’s about time… Pull the switch and enter the 2023! appeared first on EEP - Electrical Engineering Portal.

Capacitive voltage transformers (CVTs) are used on higher voltage levels, starting from 66 kV and upwards. The type of the CVT is always a single-pole one, thus the connection is between phase and earth. The higher the voltage level is,... Read more

The post Capacitive Voltage Transformers (CVT) For HV Measurements appeared first on EEP - Electrical Engineering Portal.

Power can be provided from mains power or from local gas turbines or diesel generator sets. Large facilities have high power demands, from 30 MW and upwards to several hundred MW. There is a tendency to generate electric power centrally... Read more

The post Typical electrical distribution scheme and SCADA system of an oil/gas production plant appeared first on EEP - Electrical Engineering Portal.

The printable daily warm-up helps students master important reading skills with a passage on American history and reading comprehension questions about Betsy Ross.

Hydropower plants, one of the major sources of energy in countries with an abundance of water resources, have unique generation and power evacuation characteristics. From mere kilowatts to thousands of megawatts, they come in every shape and size. In this... Read more

The post Major steps in designing generation and power evacuation in large hydropower plants appeared first on EEP - Electrical Engineering Portal.

Nowadays, when we all see and feel the colossal crisis looming on the horizon, the question of energy security is among the first things on the table in each country’s management. It’s now essential more than ever for each country... Read more

The post Electrical engineering for hydropower, from run-of-river to pumped storage plants appeared first on EEP - Electrical Engineering Portal.

Passengers will be able to use their mobile phones as tickets from this spring London, 23rd April 2014 – Thames Clippers today announced that they have signed a five year contract with Masabi, the leader in mobile ticketing and payments for transit, to bring smartphone ticketing to its River Bus […]

The post Thames Clippers and Masabi to Launch Mobile Ticketing on Central London River Bus Services appeared first on Masabi.

As part of our announcement that we have entered a global partnership with MasterCard, Masabi’s Head of Innovation Ben Whitaker and MasterCard’s Head of Transit Centre of Excellence sat down to explain why we believe working together will help customers get around cities and how this benefits transit operators. If […]

The post Masabi and MasterCard Partnership Video appeared first on Masabi.

Most compensation banks are controlled stepwise. For this purpose it is essential to ‘know’ when it is allowed to (de)activate a capacitor step by the power factor relay (controller). The so-called C/k value is calculated by the step size C... Read more

The post How To Control Reactive Power In Larger Electrical Plants With Multiple Incomers appeared first on EEP - Electrical Engineering Portal.

The purpose of a capacitor bank’s protective control is to remove the bank from service before any units or any of the elements that make up a capacitor unit are exposed to more than 110% of their voltage rating. When... Read more

The post How to control and protect capacitor banks before something goes wrong appeared first on EEP - Electrical Engineering Portal.

Things are changing fast, really fast. Technology we used a few years ago is now obsolete, and if you take a look for a second – it’s always about power availability, efficiency, and safety. This technical article deals with Schneider... Read more

The post Isolation power solutions for ultimate power availability, efficiency and safety in hospitals appeared first on EEP - Electrical Engineering Portal.

This article provides guidance on how to conduct gas monitoring and explains the various alerts that can be set. The many sorts of defects that might lead to partial discharges are discussed, and various partial discharge measuring techniques are described,... Read more

The post SF6 Gas Monitoring and Alarming Practices in Gas-Insulated Switchgear (GIS) Systems appeared first on EEP - Electrical Engineering Portal.

Acquiring the skill to operate a nuclear reactor bears resemblance to acquiring the skill to pilot an aircraft. The majority of airplane pilots rapidly acquire proficiency in performing take-offs and landings. The process that requires significant time and exertion, particularly... Read more

The post What can go wrong with the nuclear power plant in the case of a grid loss: What to do? appeared first on EEP - Electrical Engineering Portal.

The Substation Automation Systems, often known as SASs, are responsible for a tremendous variety of tasks. These include some extremely important actions, such as clearing faults in a timely manner in order to maintain the physical condition of power system... Read more

The post The true art of control, monitoring and protection provided by Substation Automation Systems appeared first on EEP - Electrical Engineering Portal.