Hi,

I'm a newbie and I'm working on a mixed-signal chip in Innovus. I've got a few analog LEF files that I've imported into my floorplan as macros.

My chip has got two power domains - VCC and VBAT.

One of the macro in the VBAT domain uses VBAT and GND as power rails KrogerFeedback.com.

On doing Special-Route, I've got a lot of minute power rails for the standard cells, as expected.

But, the VBAT power rails are not getting extended till the outer power rings. Only the GND rails are correctly getting extended till the outer power rings.

A screen shot is attached for reference.

Thanks for any help

Are they basically the same thing? I am trying to get as much experience with Allegro since a lot of jobs I am looking at right now are asking for Cadence Allegro experience (I wish they asked for Altium experience...). I currently have access to PCB Editor, but I don't want to commit to learning Editor if Allegro is completely different. Also walmart one, are the Cadence Allegro courses worth it? I won't be paying for it and if it's worth it, I figure I might as well use the opportunity to say I know how to use two complex CAD tools.

Hello, I am using Encounter 8.1. My mouse is working fine, but my keyboard is not working well in Encounter. I can type in some boxes, but in many boxes I cannot type. The binding key is also not responding. How do I fix this issue? Thanks.

Hi, I am new to cadence. I started out designing an inverter and ran LVS. I made sure that the labels are matching in both schematic and layout. But I run into the following error while LVS  stating that "No matching sub-ckt found for NFET and PFET". Can someone provide insight into this?

Respected sir,

How can i design and simulate cmos inverter using digital flow and also ineed to do prelayout ans post layout for the same cmos inverter..can i use cadence encounter for this experiments

Hi,

I was wondering if it is possible to save the coordinates of each stripe and row of the power grid 

and if it is possible to find out the effective resistance between two given points using Voltus

My goal is to built a resistance model of the power grid

Thanks

This are the Errors i am getting can you please provide the solution.

Checking out license: Genus_Synthesis (12 seconds elapsed).
License 'Genus_Synthesis' (main version: 17.2, alternate version: 17.2) checkout failed.
Checking out license: Virtuoso_Digital_Implem (12 seconds elapsed).
License 'Virtuoso_Digital_Implem' (main version: 17.1, alternate version: 17.1) checkout failed.
Checking out license: Virtuoso_Digital_Implem_XL (12 seconds elapsed).
License 'Virtuoso_Digital_Implem_XL' (main version: 17.1, alternate version: 17.1) checkout failed.
Cannot obtain 'Genus_Synthesis' license.
Abnormal exit.

How can I make innovus start with common UI instead of legacy? When I launch Innovus with command "innovus", I get the legacy UI. I have Innovus version 17.11 installed. 

Thanks in advance.

I have a set of pads for use in a design and I was wondering which attributes should I put on each pin.

Let's say it has the following pins:

   - inh_vdd, inh_vss, CORE, PAD where the first two are for the pad rings, the CORE pin is to use in the die and the PAD pin is the bonding pad.

I guess CORE would need:

   CLASS CORE

   USE POWER  (or GROUND if this happened to be a ground pad)

What about the inh_vdd and inh_vss? Theyu would not have the CLASS CORE, but would I use USE POWER/GROUND on them too?

   USE POWER (or GROUND)

   SHAPE ABUTMENT

And the bonding pad? Should I put it in the LEF? Or would that cause confusion to innovus or Voltus? And what attributed would it use? USE POWER/GROUND only?

Do I need anything in the LEF to indicate that the pin CORE and the pin PAD are essentially the same thing, just different places on the same power pad?

I have been using Voltus to do IR drop analysis but I got caught on one signal. It is negative. When I use:

set_pg_nets -net negsupply -voltage -5 -threshold -4.5 -package_net_name NEGSUP -force

Voltus dies with a backtrace. Looking at the beginning of the trace you see it suggests that the problem is it set maximum to -5 and minimum to 0. Is there another way to express a negative voltage supply for IR drop analysis?

I recently received a student version or OrCad, which I was able to download and install without trouble. However, I do not know how to setup my license.

I received the license file in an email. The instructions within the file were to include my hostname and the absolute path. I do not know what the path should point to so I left it empty. 

I was able to setup the licence server using the license file without any issues. However, setting up the licence configuration utility gives the following messages:

A user environment variable name CDC_LIC_FILE is found. The CDC_LIC_FILE settings you make will be overwritten by this user level variable. Furthermore, I get the error:

ERROR: Unable to update the CDS_LIC_FILE license path environment variable. 

This is preventing me from using any of the software.

What are the steps to installing the license and how could I resolve this error?

Thank you

Hello everyone,

I am Vinay and I am currently developing some digital circuits for my chip design for my master's thesis at University at Buffalo.

I am fairly very new to Verilog and I don't seem to follow some of the things others find very easy.

Following are the things that I want to do to which I have no clue:

1. Develop certain arithmetic functionality in Verilog

2. Generate netlist for the verilog code

3. Feed the netlist file to Cadence encounter to be able to generate Digital Circuits' layout for my chip

I can use Cadence Virtuoso and Encounter for this but I don't know the exact procedure to get this done.

Could someone please describe the detailed process for doing the things mentioned above.

Thank you.

According to the book Electronic Design Automation For Integrated Circuits Handbook there are mutiple algorithms available. Quote from book: "One of the first complete ATPG algorithms is the D-algorithm [9]. Subsequently, other algorithms were proposed, including PODEM [14], FAN [15], and SOCRATES [10]."

I was wondering which algorithms are used in Cadence Modus.

Hi! 

In my design, there is an one hold violation on scan path, test data is corrupted during scan cycles (when i run verilog simulation of test vectors). I created constraint 'falsepath' to 'TI' input of violated flop and load it into Modus, but this does not have effect.

Can enyone explain to me, does 'falsepath' constraint affects scan path (from Q to TI/SI input, i.e. during SCAN procedure) or this constraint is only for functional mode (ie affects TEST cycle only - to 'D' input)?

I hope resolve this problem this by using some modus design constraints or any other method.

I have completed physical design of a block in innovus. I want to extract rc of that block using quantus .  It will be very helpful if you give step by step procedure and command to run quantus to extract rc of that block.

Hi,

When I import the top level Verilog file generated by Genus into Virtuoso, the power pins are left unconnected. I tried different configurations in "Global Net Options" tab. However, nothing changed. 

The cell is imported with three views, namely functional, schematic, and symbol. In www krogerfeedback com functional view everything looks OK, that is the top level Verilog file. In schematic, I can see the digital cells but VDD and VSS pins of the blocks are not connected. In the symbol view there are no pins for VDD and VSS. 

On top, we are trying to implement a digital block into Virtuoso. The technology is TSMC 65nm. On Genus and Innovus, everything goes straight and layout is generated successfully.

Thanks.

Hello,

I created a floorplan view in Virtuoso ( it contains pins and blockages). I am trying to run PnR in Innovus for floorplan created in Virtuoso. I used  set vars(oa_fp)    "Library_name cell_name view_name"   to read view from virtuoso. I am able to see pins in Innovus but not the blockages. Can i know how do i get the blockages created in virtuoso to Innovus.

Regards,
Amuu 

HI, I have been using the Innovus GUI commands for several things and wonder if those command can be written to a log or cmd file so I can use it in my flow script? Is there such options that we can set?

Thanks

Hi,

I am doing layout for a mixed-signal circuit in Innovus. I want to create a digital donut style of layout (i.e. put analog circuit in the middle, and circle analog part with digital circuits).

To do that, I need to place some pins inside the edge to connect to analog circuit (as shown in my attachment), but the problems is that I cannot place pins inside the edge by using "pin editor" within Innovus. Any suggestions to place pins inside?

Thank you so much for your time and effort.

Hello Everyone,

I was finishing the layout via Innovus and ran verifyConnectivity followed by checkRoute.

verifyConnectivity was okay and it showed no errors and no warnings, whereas checkRoute showed there are 3 unrouted nets.

When i ran the checkRoute command again immediately, it showed no unrouted/unconnected nets.

Which of these commands should we trust or is this really unrouted nets issue?

Looking forward for a response, thanks in advance.

Regards,

Vijay

Hi,

There was tool available with INCISIV called imc to view the coverage reports.

The question is: How can we view the code coverage reports generated with XCELIUM? I think imc is not available with XCELIUM?

Thanks in advance.

Hello, i have a logic output from a D-flipflop which generates a reset signal with variable pulse width. I want to stretch this LOW pulse width with an extra 100ns added to the original pulse width digitally, is there any way to do that?

Hi All,

I have 1 huge project(day X) which has different reference power supply designs.

Now I start a new project and I require 1 specific reference power supply from X.

What is the easist way to do this, other than a copy paste.

Is there a way to create say symbols or something similar, so that multiple different people could use it if they need, in their projects

Thanks for your help and suggestions.

Hi,

I recently encountered a probelm where scrolling with the mouse wheel and [i][o] button does not zoom in or out both in "Allegro orcad capture CIS 17.2.2016 " .

When I scroll the mouse wheel or [i][o] button, nothing is done.

The thing is that it worked fine until yesterday.

Anyone has an idea?

Thanks,

Dung.

When I enable clock gating in my synthesis flow (using Genus 18.15), my simulation (using Xcelium) on the post-synthesis netlist fails. The simulation succeeds pre-synthesis and also if I remove clock-gating in the design. I use set_db  lp_insert_clock_gating true to enable clock gating during synthesis. I printed out some of the signals from the netlist and can see where it fails (it incorrectly writes a register). However, I am not sure how to solve this issue or what I should be looking for. Any help would be appreciated. Thanks.

Dear all,

I am using Conformal Constraint Designer (Version 17.1) to analyse a SystemVerilog based design.

While performing default HDL checks it finds  some violations (issues) in RTL and complains (warnings, etc) about RTL checks and others.

My questions:

Is there any directive which I can add to RTL (system Verilog) so that particular line of code or signal is ignored or not checked for HDL or RTL checks.

I can set ignore rules in rule manager (gui) but it does not seems effective if code line number changes or new signals are introduced.

What is the best way to customize default_hdl_rules ?

I will be grateful for your guidance.

Thanks for your time.

Hi,

Is it possible to use a SystemVerilog package which is compiled into a library and then use it in a VHDL-2008 design file? Is such mixed-language flow supported?

I'm considering the latest versions of Incisive / Xcelium available today (Oct 2019).

Thank you,

Michal

hi all, 

          what wrong with the error "param_write.log does not exist" when i export parameters in allegro 16.6 pcb board.

          someone can provide suggestions, thanks.

best regards.

For a netlist vs. netlist LEC flow we have to solve the following problem:

- in the RTL code we replicate a large array of N x M all-identical hard-macros, let call them MACRO_A

- MACRO_A is pre-assembled in Innovus and contains digital parts and analog parts (bottom-up hierarchical flow)

- at top-level (full-chip) we instantiate this array of all-identical macros

- in the top-level place-and-route flow we perform ecoChangeCell to remaster the top row of this array with MACRO_B

- MACRO_B is just a copy of the original MACRO_A cell containing same pins position, same internal digital functionality and also same digital layout, only slight differences in one analog block inside the macro

- MACRO_A and MACRO_B have the same .lib file generated with the do_extract_model command at the end of the Innovus flow, they only differ in the name of the macro

- when performing post-synthesis netlist vs post-place-and-route we load .lib files of both macros in Conformal LEC

- the LEC flow fails because Conformal LEC sees only MACRO_A instantiated in the post-synthesis netlist and both MACRO_A and MACRO_B in the post-palce-and-route netlist

Since both digital functionality and STD cells layout are the same between MACRO_A and MACRO_B we don't want to keep track of this difference already at RTL stage, we just want to perform this ECO change in place-and-route and force Conformal to assume equivalence between MACRO_A and MACRO_B .

Basically what I'm searching for is something similar to the add_instance_equivalences Conformal command but that works between Golden and Revised designs on cell primitives/black-boxes .

Is this flow supported ?

Thanks in advance

Luca

I have a file that list all the `defines that is used in the current design. This file (define.vh) is generated, like so :

`define MACRO_1 5

`define MACRO_2 1'h0

... etc

But in genus when I run the command

read_hdl define.vh

read_hdl -sv top.sv

The tool work as if the defines never get parsed and returns with unreferenced errors. How can I resolve this? Do I have to include 'define.vh' in all the design files?

The following is valid SystemVerilog:

module mmio
#(parameter PORTS=2,
parameter ADDR_WIDTH=30)
(input logic[ADDR_WIDTH-1:0] addr[PORTS],
output logic ben[PORTS], // Bus enable
output logic men[PORTS]); // Memory enable

always_comb begin
for(int i = 0; i < PORTS; i++) begin
ben[i] = addr[i] >= 'h20080004 && addr[i] < 'h200c0000;
men[i] = ~ben[i];
end
end

endmodule : mmio

And if you instantiate it:

mmio #(1, 30) MMIO(.addr('{scalar_addr}),
.ben('{ben}),
.men('{men}));

Genus returns an error: "Could not synthesize non-constant range values. [CDFG-231] [elaborate]" Is this just not possible in Genus or could it be caused by something else?

As title,

How to dump waveform, fsdb in SimVision? 
(Simulation Analysis Environment  SimVision(64) 18.09-s001)
Please help.

Thanks.

Unable to open Source Browser. It goes into an infinite loop of loading, with the hour glass displayed and message "loading snapshot".

The deisgn was compilied with "15.20.s028" and that is the same version of simvision I am using to open the code.

The waveform viewer is uo and so is the Design Browser. I can take signals from Design Broweser and view the waveform viewer,

but the source brower hangs.

What should I be looking at to resolve this situation. Many of us at the company are sufferring from it. Colossal waste of time.

. 

hello sir this is Ganesh  from NIT Hamirpur pursuing MTech in VLSI. I have doubt regarding SDF i'm using genus tool for synthesis & after synthesis when i'm generating SDF it is giving delays by default for maximum values but i want all the delays like minimum:Typical:Maximum how can i do this. Is there any provision to set PVT values manually for SDF generation so that i can get all the delay values.

HI!

I want to use map_to_mux pragma for a particular logic in my code, which is in generate block. 

module xyz

parameter P_IN_WIDTH= 100

parameter P_OUT_WIDTH =100

parameter P_XXX = 1

parameter P_ZZZ=1

parameter P_IN_OFFSET_WD = 10

input [P_IN_WD-1:0]  in_data;

input [P_IN_OFFSET_WD-1:0] in_offset;

output [P_IN_WD-1:0]  out_data;

generate
if (P_XXX == 1)

// cadence infer_mux "MUX"
// cadence map_to_mux "MUX"

begin : XXX

assign c_out = (in_data >> in_offset*P_ZZZ);
end
else

// cadence infer_mux "MUX"
// cadence map_to_mux "MUX"
begin : YYY
assign c_out = (in_data << in_offset*P_ZZZ);
end
endgenerate

endmodule

How to get minimum: typical: maximum values in SDF I am using Genus synthesis tool there default setting is for max value. But I want all the values please guide me.

Which things we have to mention in SDC for combinational design? How to create virtual clock? 

I have been working on a an ASA 17.2 project for the last 6 months.

When I go to Project --> Settings, the settings window does not open. 

The tool indicates that a window is open, as I cannot click on anything else in the project. But it does not show the Settings window.

This has been happening only for the last 2 months. Before that it was working fine.

If I send the project to my colleague, the settings window shows up for him.

Hi,

I am trying to use "sed -e 's " from SKILL code to edit unix file "FileA", to replace 3 words in the 2nd line.

How to run below multiple commands using  ipcBeginProcess, Should I use ipcWait or ipcCloseProcess ?

Using && to combine , will that work as I have to work serially on each command. ?

With below code only the first command gets executed. Please advise.

FileA="/user/tmp/text1.txt"

sprintf(Command1 "sed -e '2s/%s/%s/g' %s > %s" comment1 get(form concat("dComment" RDWn))->value FileA FileA)
cid = ipcBeginProcess(Command1)


sprintf(Command2 "sed -e '2s/%s/%s/g' %s > %s"  Time getCurrentTime() FileA FileA)
cid1 = ipcBeginProcess(Command2)


sprintf(Command3 "sed -e '2s/%s/%s/g' %s > %s"  comment2 get(form concat("Duser" RDWn))->value FileA FileA)
cid2 = ipcBeginProcess(Command3)

Thanks,

Ajay

Hi,

I am trying to write a skill code where it takes form inputs by default and just displays tree directly.

i have written below code,

procedure( create_tree()
let(()

leHiTree()
leTreeForm->treeOption->value="Current to user level"
leTreeForm->userLevel->value= 31
ipcSleep(1)
hiFormDone(leTreeForm)

))

the form takes in values but it is not closing.

tried with regtimer in place of ipc sleep, didn't work.

how to close form(should be same as pressing OK)? 

Thanks in advance,

vishwas 

I have a technology library (given by foundry) with leLsw layer section defined.
I do not want to touch it

I added few layers with an ITDB approach. Now I'm unable to see the added layers, as it is not present in the leLsw layer section of the main techlib.

I want the user of the new techlib to see all the layers by default.(I don't want the users to go to the properties of palette and switch the display option to techfile layers instead of leLsw)

Hello,

I am in a need of a skill program to find all instances of a specific cell (Including Mosaics), throughout the hierarchy. The program should print the instance's name, xy coordinates at the top level, and extract a label name that is dropped on top of it. In case there is no label on top of the found instance, the program should print "No Label Found" in the report text file. This program aims to map PADs cells within top level.

I am using the below Cadence's solution to find instances and it works well. The missing feature is to identify LABELs that are on top of the found instances. 

I tried to use dbGetOverlap() function, within the below code, in few setups but it seems to fail to identify the existence of labels on top of the found instances.

For example: 

overlapLabel=dbGetTrueOverlaps(cv cadr(instBox) list("M1" "text"))

I am interested to add to the Cadence's solution below some code in order to identify labels on top of the found instances.

Any tip would be greatly appreciated.

Thanks,

Danny

--------------------------------------------------------

Hi,

I want to convert ircx file(which is from TSMC,inclued EM Information) to ict or emDataFile for Voltus-fi.

I tried many way, but I can not make it. Can anyone give me some advice?

and I  do not installed QRC.

below is some tools installed my server. 

IC617-64b.500.21 is used.

Hi,

I have a test session object that I am getting like this:

maeTstSession=maeGetTestSession(test ?session session)

Is it possible to get the test name from this object? I am asking because this object passed to several levels of functions and I don't want to pass an additional argument with the test name

Hi,

I would like to add items like length of selected metal or area also in status tool bar. I have tried below option but I am getting warning as shown below. Could you please give suggestions. 

envGetVal("layout" "statusToolbarFields")

*WARNING* envGetVal: Could not find variable 'statusToolbarFields' in tool[.partition] 'layout'

Regards,

Varsha

Hello,

I have created an appForm with  the following attachmentList and size:

?attachmentList list(hicLeftPositionSet | hicRightPositionSet ; field 1
                     hicLeftPositionSet | hicRightPositionSet ; field 2
etc.

?initialSize    800:800
?minSize        800:800
?maxSize       1600:800

If I reduce the minimum y-size (?minSize        800:200), scrollbars are not inserted, unless I remove the attachmentList constraints.

Is it possible to have both scrollbars and "hicLeftPositionSet | hicRightPositionSet"? 

Thank you,

Best regards,

Aldo

I can get the bound stdcells using bndGetBoundObjects, but not get what each individual stdcell corresponds in layout.

Is there a way to get the layout bound stdcells of an array schematic symbol if the layout stdcell name do or do not match the symbol naming?

Once the schematic array stdcells are bound to the layout stdcells, how to get the correct terminal term~>name and net~>name?

Example of a schematic symbol and layout stdcell:

Schematic

INV<0:2>    instTerms~>terms~>name = ("vss" "vdd" "A" "Y")

                   instTerms~>net~>name = ("<*3>vss" "<*3>vdd" "in<0:2>" "nand2A,nand3B,nor2B")

Layout ( I know it is bad practice, but it happens )

stdcell1 instTerms~>terms~>name = ("vss" "vdd" "A" "Y")

             instTerms~>net~>name = ("vss" "vdd" "in<0>" "nand2A")

I23        instTerms~>terms~>name = ("vss" "vdd" "A" "Y")

             instTerms~>net~>name = ("vss" "vdd" "in<1>" "nand3B")

INV(2) instTerms~>terms~>name = ("vss" "vdd" "A" "Y")

             instTerms~>net~>name = ("vss" "vdd" "in<2>" "nor2B")

Paul

Hi Team,

Problem Statement:In hierarchical layout, I want to get BBOX of particular layer without actually flattening the layout.

Description:The layer can be at any hierarchical depth i.e both from PCELL or shapes but at top level if they are overlapping then I want the merged BBOX.

Now, I am able to get BBOX of all the shapes present at different hierarchy.But i finding issue in merging BBOX.

Please can help me on the same issue as I require efficient way to merge the BBOX because list containing the BBOX is huge.

Thanks in advance.

Regrads,

Prasanna

Inside the scope of isCallable there is code which I don't want to be executed.

The procedure named in isCallable to-day is callable.

I want to make that procedure so it cannot be called.  How do I do that?

I can't change the isCallable line or the scope.  I want to change its behavior by making sure that the procedure does not exist (obviously this would be done before the code is executed).

I have a SKILL script that executes the callback of a menu item, and depends on first redefining an environment variable. 

When a user interrupts the script with ctrl-C, the script cannot finish to set the environment variable back to its default value.

How can I write the script in a way that handles a user interrupt to reset the changed environment variable after the interrupt?